I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
Does rbc_mesh_value_enable() API is designed for ? and how should I use it? and what does its parameter handle mean? Is it has the same meanning as the parameter handle of...
I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
While migrating to the latest nRF5 SDK (17.0.2) and nRF for Mesh SDK (5.0.0) , I've noticed that they ship with Softdevice 7.2.0 .
The latest s132 Softevice available for...
Hi,
I understand that scan request allows the broadcaster to send additional advertising data. Does it send the additional data via data channels? Is it related to secondary...
SEGGER ver 5.50d
nRF52840
I'm trying to find a way how to use the STL library with GCC compiler. I know that SEGGER is not fully supported STL library (a basic stl library...
Hi,
We are developing a solution using nRF52 and nPM1100 using nRF5 SDK 17.x? I was wondering if there is a software library already written for the nPM1100?
Thank you...
Is it possible to change the smartbasic firmware? and if I want to return to that firmware how can I doit?, and last one, if I use de nordic SDK with the DVK BL654, does it...
Optimization level is set to "Debug". Tried to change it to one of the Levels, however then firmware does not run at all. Debugging Level is set to Level 3.
Can it be other...
I want to develop the nRF series at segger embedded studio for the first time. But I tried the following homepage to install manually. www.nordicsemi.com/.../Segger-Embedded...
NCS(nRF Connect SDK) is a good environment to develop nRF52,but it seems not stable until now.
I want to use NCS(nRF Connect SDK) to develop my project ,and met some unknown...
Hi Supporter,
I use apptimer in proprietary_rf gzll, I used as below ,but it doesn't work.
1) app_timer_init(); ,here I ennable the RTC1 in the sdk_config.h
2)app_timer_create...
Hello NRF ,
I have been using NRF9160 DK GEN-1 board for NB-IOT and GNSS tracking and able to configure my network SIM as well as the NRF cloud .
I have used SDK 1.4.2...
Hello There,
Basically I just want to get Sensor data like (Temp Sensor) who already connect to Arduino and I get it , So I just want that data to nRF9160 over UART in...
Refer to nRF52840 Technical Manual USB 2.0 (full speed (12 Mbps) controller) The USB2.0 rate can be up to 480Mbps. We have a product whose USB transmission rate must not be...
I have created a program code on the Adafruit nRF52840 express in the Arduino IDE. I want to read this program code (including bootloader) via my j-link edu mini and save...
I noticed that the nRF Connect SDK has kept up with ZBOSS updates throughout the year. Is there a plan or recent releases with regard to the "nRF5 SDK for Thread and Zigbee...
