Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
I have a question about Makefile template used in all samples in SDK12.x
What is the sense of:
$(foreach target, $(TARGETS), $(call define_target, $(target)))
-include...
Has anyone used a graphics library like emWin or TouchGfx on nRF52?
www.segger.com/emwin.html
http://touchgfx.com/en/
I do not see any posts on either forums or here...
Hello,
I'm developing a project based on the NRF5340 and have encountered some challenges. As I'm relatively new to C, I'm trying to implement a quadrature (incremental...
Hi,
I was just sent at nRF9160DK from a client to have a play with and test modem functionality for a future product in development.
I have followed the get started instructions...
Hello everyone,
I have some questions regarding the active discharge of the load switch in LDO mode. We have an in-house hw with the nPM1300 configured as described in the...
HI
.
It was configured to detect low voltage of the battery using lpcomp.
This configuration is already being used in mass production of other products and there have...
Hello guys,
I was refreshing BLE concepts by doing the BLE Fundamentals once again and I have faced some trouble with the nRF5340 dk on Lesson 2. I have built the application...
Hi,
we have nRF54H20DK (SoC rev. "C"). connected to MAX77655 via I2C (SCL ~ P1.0, SDA ~ P1.4 according to I2C restriction).
I am trying to test i2c131 for reading/writing...
Hello,
We are using DFU target library with MCUboot (Connect SDK v2.9.0):
And we are getting assertion fail on first dfu_target_offset_get() call after FW update:
...
Please confirm whether the "sample app nrf5340_audio" in "v2.8.0" supports "GAIN control" in "SPI+GPIO mode". the method to enable "GAIN control" in "SPI+GPIO mode" if the...
Hi Nrodic，
Does NRF5340 have an example code for QSPI driving uLED display peripherals (for example, I need to drive this display chip: JBD013VGA， As per the attached...
I'm following along with the Nordic Academy tutorial for v2.7.0-v2.9.0. I made the recommended modifications to my v2.9.0 project with an nRF54L15-DK target:
Create sysbuild...
Hello! I am developing my own BLE solution where I have the different attributes in my service and I am connecting two different nrf52840, one to act as a GATTClient and one...
I am attempting to do a simple read from the FEM on the nrf21540-DK board. I should be able to use the zephyr driver with spi3 (or fem_spi) to do a simple read/write from...
I'm writing a client/central application connecting to a peripheral, discovering a service, and then wishing to enable notifications from a specific characteristic.
Once...
Hi,
I am trying to write a file to the FAT file system on nRF7002 board.
Here is what I have tried:
in proj.conf:
ONFIG_FILE_SYSTEM =y
CONFIG_FLASH =y
CONFIG_FLASH_MAP...
Hi,
we have nRF54L15DK (rev. 0.9.1). connected to MAX77655 via I2C.
I am trying to test i2c21 and i2c22 for writing data. I have tested it on different SCK and SDA on...
