I use two nRF51822 boards running the ble_mesh_gateway sample project. I have modify the project slightly so to work on my board(juts modify the GPIO configuration , LED and...
Hi,
I use nrf51822 HID keyboard.
How to add a game-pad report as a second report in the ble_hid_keyboard ?
How to init the function hids_init() in SDK.
Thanks
Gamepad...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
Hi Support Team
Is the oversampling mode the highest accuracy mode for the SAADC of nRF54L15? The datasheet mentioned a formula to calculate the improved SNR. What is the...
Hi Team, I tried adding battery reporting to the Matter bulb demo based on the nRF54L15DK. The device was successfully added to the Apple Home app, but I’ve noticed that it...
Hi,
I'm trying to enable support for MT25QL01GBBB memory on nrF5340DK. Existing flash has been soldered-off, the one from Micron has been soldered-in with two pull-up resistors...
Hi, I was curious if the orientation of the devices matter for channel sounding using NRF54l15. I have noticed that channel sounding works best when the initiator and reflector...
Hi,
I am trying to get an nRF54L15DK working with an nRF7002EK using SPI (not QSPI) and I cannot get this working using the wifi-scan sample.
I am using nRF Connect SDK...
I'm attempting to migration from using MCUBOOT as a child image to sysbuild using SDK 2.8.0.
Everything boots fine when building using a child image, but when switching...
Hello, I tried the example from the exercise. I dint change anything which means I didnt activate timeslicing yet and I already get the output: Hello, I am thread0 Hello,...
I flash my firmware onto the nRF52840-DK and want to profile the power consumption of the nRF52840 chip, but not the other DK specific stuff like JLink. How do I exactly wire...
Using connect SDK 3.0.2 and a NRF-DK52840 my goal is fairly simple: My app should be updatable via BLE using a static partition table. I followed this tutorial: nRF Connect...
Hi,
I am trying to set up a half duplex UART in async mode over pin 1.9 on NRF54DK board for my project:
Overlay file:
& uart20 {
compatible = "nordic,nrf-uarte...
Hello Nordic
We're developing an application where the second firmware partition is saved in external storage, which we would like to be accessible by both MCUboot and the...
I will calculate the capacitance of the external capacitors for the 32 MHz oscillator circuit, but the values of the Cpin for XC1 and XC2 are not specified in the the datasheet...
When I follow the use_gpio_pin_directly manual I get a compilation error:
```
/home/gal/dev/ism330bx_driver_contribution/zephyr/include/zephyr/devicetree.h:196:36: error...
Hello,
I'm tinkering (motion detection mostly) with a Thingy:91 unit (I don't have a DK board), and in general it works fine reporting sensory data to AWS IoT Core.
Last...
