Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I'm trying to program a custom board with a Raytac nRF52832 module using the nRF52 DK's onboard J-Link via the P20 debug out port. The J-Link only detects the onboard nRF52832...
Hi,
I've been working through the Nordic Bluetooth ESL Tutorial and have the sample code up and running (using a nRF52833 DK as the tag and a nRF5340 DK as the access point...
We have custom hadware which we can successfully added the bootloader. We can generate .bin files & bootload them via BLE using the Nordic devicemanger app on our smart phone...
I am using NCS V3.0.2 with a custom nRF52840 board, which functions as a BLE peripheral. The application that I am working on fully depends on the BLE connection, so the crucial...
Hello. We need to add more end devices than default (10) on our Zigbee coordinator and that was solved with
zb_set_max_children( ZB_DEFAULT_MAX_CHILDREN );
where ZB_DEFAULT_MAX_CHILDREN...
Hi, I use nrfconnect SDK 3.1.1 and nRF52840 (as a dongle, DK etc) Using the power profiler kit 2 I see legacy advertising (TX/RX) peaks of about 32mA (with txpwr=8dBm, 3.2V...
Hi guys,
I'm working on this project which was basically a migration from STM32 to the nordic NRF52832 in order to enable the BLE beaconing mode.
It has been a challenge...
Dear Nordic Support,
I’m working with a Thingy:53 device and encountered a persistent issue during recovery. The device is recognized via J-Link (serial number: 1057760136...
Hi everyone, I'm trying to set up a bootloader chain using sysbuild (NSIB → MCUboot → APP) so that MCUboot can act as an upgradable bootloader. I'm working with the nRF54L15...
What is the permitted VDD ripple on the nRF9151?
I see " To minimize supply voltage ripple and suppress EMI coupling to and from nRF9151 VDD , keep supply network impedance...
Hardware Setup
Custom Board:
nRF52811 chip
No external LFXO (32.768 kHz crystal)
No LC filter for DC-DC regulator
No peripherals connected (no LEDs, buttons, sensors...
Hi,
I try to use the west ncs-sbom command to generate the result, however i meet below error happening but I had not idea how to solve it could someone help me to check...
The issue is that , i have custom board which have nrf52833 and nrf21540 (Range extender) , i have to increase the range of tx gain = 20dbm using gpio method
this is my...
Hello,
I have developed a bootloader with OTA update functionality on an nRF device. The partition switching code (bootloader jumping to the application after OTA) works...
