VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
Hi.
I am developing PCB where there is a Wifi module ESP32-WROOM and a nRF52833 connected via 2-wire UART interface (TX/RX only), there is no way to use 4-wire UART because...
EDIT: We found the reason for this and it is a hardware issue. This question can be deleted as it is no longer valid.
-----
Hello,
We are currently developing a...
Hi!
When opening the LTE Link Monitor in nRFconnect 3.7 under Linux (Ubuntu 20.04) only a "whitescreen" appears after I select the device. The application is not visible...
Hello,
I am using NCS v1.5.0 and would like to check is a KMU slot is being used or not. I erased the whole SoC and tried reading the directly the registers, in secure mode...
which pins can be used as PWM output pins in nrf52811.
Can I use them directly or I need to add some hardware to use the PWM feature.
I have an NRF5811 SOM (EYSNCNZWW...
Hi Sir/Mdm, I want to use 1.54 inch e-paper module from waveshare with nRF52840 dongle with Zephyr RTOS. I have read the documentation from Zephyr about the display and noticed...
Hi,
We use the nRF52840 and have now run out of space using debug mode compilation (using CMake from bash).
When we compile in release mode, we get 50% full flash, so...
Hi,
I am using nrf52832 and mesh sdk 3.1.0 with nrf5 sdk 15.2.
We use dual bank approach for our firmware update with the normal nrf5 sdks ble bootloader. But now our...
Hi.
I have been trying to implement my own Model into the Light Switch Example (Mesh SDK 4.2, SD s140 7.0.1, Hardware: nrf52840 DK), according to this Thread:
Adding Simple...
I'm implementing the WS2812 driver on custom hardware and have some confusion around the hardware tuning parameters for the SPI implementation. The description of the device...
Hi everybody,
We ran into a Zephyr configuration issue which is related to Zigbee and Zephyr's networking stack. In our setup we would like to use Zephyr's modem library...
Hi,
I have nRF52840 DK, for nRF52 series devices. I switched from nRF52 SDK to nRFConnect SDK.
I reviewed
http://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest...
