void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-9-bootloaders-and-dfu-fota/topic/exercise-3-dfu-with-external-flash/
I have this exercise...
Hi Nordic Semi,
Instead of using NRF52 for previous projects, I am new in NRF54L15 and zephyr.
I have started the blinky pwm sample in VSC and tried a lot to just...
Hey
Do the hardware in the NRF5340 support what is needed for Bluetooth classic.
I do know that there are no software support and no plans for supporting it, but if...
Dear DevZone support,
I'm currently evaluating nPM1300 for Lithium Polymer battery management and charging and would like to ask a question.
I understand that I can...
The documentation for the QoS dynamic parameters command "+CGRQOSRDP" specifies that the uplink and downlink maximum bitrates are in units of kbps, with a maximum value of...
Hello,
we are using the direct test mode example of NCS with an nRF5340.
Now we got a question from the testlab, about the transmit power parameter.
The setting in...
Hi,
The attached code is based on a sample code from NCS v2.9.1 and creates a LittleFS flash disk on external SPI NOR onboard nrf54L15DK. There is a mismatch in the code...
Hello. I am using vscode. I added sdcard to broadcast_sink in the existing samples in applications/nrf5340_audio and checked the list with the serial monitor and wanted to...
We want the system to be in low power mode in idle state. Therefore after advertisement is sent the BLE is switched off using bt_disable. The return for this function is fine...
Hello, I am using peripheral uart as my base project and uppn that, I have built my application.
I am delibrately changing the flash region just to see if i can modify flash...
Hello, I can commission nrf52840 bulb by iPhone successfully using below QR code:
https://project-chip.github.io/connectedhomeip/qrcode.html?data=MT%3A6FCJ142C00KA0648G00...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
I am trying to make a FOTA to update the firmware of the nrf9151 using the command AT#XFOTA, the issue I am having is that I am unable to have the app_update.bin file generated...
Hello, I am currently working with NRF5340-DK dev kit and I want to use 2 SPI devices connected on the same SPI bus OR use 2 different SPI instances, however none of these...
