We are having a slight issue when we are trying to update the DFU. The original version had this setting for the data reserve:
#ifndef DFU_APP_DATA_RESERVED
#define DFU_APP_DATA_RESERVED...
Hello!
I am working with the example mpu interface projects located at the following repo:
github.com/.../nrf5-mpu-examples
After converting the Keil projects to...
I'm using S332 0.9.1 with freertos. nRF52.
BLE and ANT are both active. I would like to run the ANT continuos wave (CW) test after a specific trigger (a command over a console...
I want to encrypt advertisements using aes-ccm peripheral present on the nrf51 board. I am not using softdevice, instead I am generating my own packets and transmitting them...
Currently, it using the I2S at nRF52832.
I want to play the wave file,But can not play well.
So, I ask you for a check because there is the following question.
[Question...
We love the radio range of the Nordic bluetooth chips. I am looking to see if anyone is developing a long-range bluetooth pendant or wearable? if so, I interested in perhaps...
I'm trying to read 8 adc channels using SPI, but then if I dont put some nrf_delay_ms the MISO return nothing and the CS is being driven low by default, high or a period of...
We are developing a sleepy end device using the nRF52840, based on the light switch sample. We have set zb_set_ed_timeout to 16384 minutes, which is approximately 11 days...
Hello,
I am using the NRF52832 in my PCB design, and I have attached a screenshot of relevant part of the layout. My PCB manufacturer pointed out that some vias overlap...
Hello,
I have had this issue from the first time I installed VS Code and the nRF Connect Extension.
When I open my project, the connected devices pane is just missing...
Hi,
Since we started testing the new nRF9151 with the latest modem firmware (v2.0.1), we’ve noticed a change in GNSS behavior compared to the nRF9161/v1.3.6.
Recently...
Hi there!
We're trying to port the FreeRTOS Cellular Interface to work with the nRF9160 which is running the Serial LTE Modem application. The problem we are facing is a...
i have a nrf52840dk that is flashed with a old program i used. i want to try the nfc tag and read it using my phone. what should i flash to my nrf52840dk in order to use it...
Hello,
I am building the existing WIFI station app for the Thingy53 with the nRF 7002EB board - sample code: nrf/samples/wifi/sta
In the CMakeLists.txt file, the line...
Hi,
we are now using nRF Toolbox -> Logger tool on our phone to monitor Thingy91 application information via UART/BLE.
Now we would to monitor/log the same information...
Hi,
I am using NCS v2.4.2 and nRF5340DK + nRF21540EK but I can not enable GPIO+SPI mode.
for example, I use nrf/samples/bluetooth/central_and_peripheral_hr application...
I manage to connect to the network and disconnect from it after sending the data, but if I'm in an area without reception, the device tries to connect and after a while, the...
: Chip Not Recognized by J-Link
I need advice from someone familiar with the nRF9160-SICA-B1A-R7.
I purchased an nRF9160-SICA-B1A-R7 chip individually from Digi-Key and...
Dear Sir :
We are now developing on nrf52840, with ncs v2.6.1 and zephyr.
We want to put I2C0 to PM_DEVICE_ACTION_SUSPEND before sys_poweroff().
Our code is below :...
Hello everyone,
I am currently trying to get a ML model running on my nRF52 (preferred nRF52832 but nRF52DK works also for me). Right now I am trying to evaluate if my setup...
We have using nrf5340-nrf7002 in our custom board. SDK version 2.6.1 We understand that the timer will not function in System OFF (deep sleep) mode. However, our project is...
Hi there,
I've encountered a strange PWM behavior and have investigated a bit. When setting load_mode to NRF_PWM_LOAD_WAVE_FORM, creating two sequence, and the latter sequence...
