VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
Hi,
I am writing to seek assistance with an issue I've encountered while attempting to create a modem trace on my nRF9160DK board.
When flashing my asset tracking code...
i have to use mqtt for my project. Now am using nrf 52840 for transfer data to from my device bt840 if i want to go with MQTT have to connect wifi module with ble.
esp32...
Hello!
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I am integrating NUS Central...
Hello!
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I am integrating CDC ACM...
I'm using version 2.0.0 of the Android version of the device manager app. When I select my device from the list to do a DFU it immediately closes the app. Normally it would...
sometimes the param update will fail and sometimes will not. May I know what the reason is and how to solve this issue?
error case;
normal case:
my prj.conf...
Below are power consumption measurements of a DUT being booted with the same PPK2 in SMU mode with various software versions. The only variable being changed is the PPK2 software...
Hello all,
I want to use nrf52840dongle to receive notifications from other BLE board.
I have tested with nRF Connect for Desktop Bluetooth Low Energy successfully.
...
Hello,
I'm using nRF5340 audio application with nRF Connect SDK v2.7.0 on nrf5340 Audio DK.
I didn't change anything in the sample code but only modifying the NRF5340_AUDIO_TRANSPORT_MODE...
Hi there,
I generated the DAC, PAI, and PAA certificates using the chip-tool and merged them into my firmware as factory data. Additionally, I generated the Certificate...
conducted an ADC experiment using the nRF5 DK (PCA10056).
The power supply for the nRF5 was provided via USB.
Based on the SAADC sample, I coded the following:
...
I am using an NRF52840DK.
1. I erase the chip to start clean:
nrfjprog --eraseall
2. I flash the MCUboot bootloader:
~/mcuboot/boot/zephyr$ west flash
The output...
Hello,
I want to operate a rather complex spi sensor with the nrf5340. To do that, I wanted to first establish spi communication. I started by creating a hello world example...
