Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Hi,
I made a DFU procedure with:
nRF52840 DK as Disrtibutor
nRF52840 Dongle as Target
Since composition data of my new firmware was the same of the one allocated on...
Hi, I am developing an application to read the ADXL355 via SPI. I have not been able to read the register of my accelerometer. And I don't know why. I tried reading the register...
Hi, I'm getting an error saying that "ble_link_ctx_manager.h: No such file or directory issue"
This is the main.c file:
Also, I have attached the snapshot of my project...
Hi!
I'm developing for nrf52832 using zephyr. I'm using the nordic hal driver in order to use the PWM with EasyDMA. The PWM is used to control a piezo buzzer. The PWM is...
I have very advanced project based on nrf52840dk for dev and custom boards for prod.
The development environment is based on zephyr build dockers. Zephyr is 3.5.0.
I would...
Hi,
I am having a hard time for days now trying to get the MCP2518FD working on a nRF9160-DK board. This device, embedding CAN transceiver and receiver, is accessible through...
Hello ,
I have a few questions about the connectivity bridge on T h i n g y : 9 1 . I 'm currently working with Bluetooth data on the nRF52 SoC and I need to transfer it...
I am building both the IOS and Android version of nRF Connect Device Manager and I am able to bootload/update my application.....but
But, we have external memory and we...
Hi there,
I want to manage certain devices that have an address and a value. I would like to dynamically add and remove devices from my data structure. I believe that using...
nRF52840-Preview-DK LED5 is off, J-Link Error.
I press IF BOOT/RESET key then poweron the PDK, no BOOTLOADER removable disk drive letter appears, I have installed the driver...
Hi all,
I am developing a sidewlk application as a replacement for LoRaWAN recently based on the sidewalk protocol implemented in the nRF connect SDK. I would like to check...
Hello,
We are currently manufacturing products using the nRF52840 with the nRF5 SDK. We are planning to develop new products using the nRF Connect SDK and are currently...
below is my develop environment .
TOOL : VSC - NRF CONNECT SDK 2.6.99 DEV : NRF7002DK
I am currently looking into the BLE GATT structure in NCS.
Since I need to use...
1. am currently using the nrf9161_dk. and have not modified the modem FW in anyway.
2. I am using the vscode extension provided by nordic to build/run this sample
a, i...
Hello, I am trying to migrate from v2.5.0 to v2.6.0. I had subghz working for the sidewalk samples in v2.5.0 but can't seem to get it working in v2.6.0. I don't see any errors...
