I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hello,
I have following problem:
I am using a multilink NUS Central. With one peripheral connection everything works fine. But when make a second connection I sometimes...
Dear support
Try to perform DFU OTA on my final target board and have an error state says - "payload(250 bytes) too long for MTU: 249 "during uploading stage, could anyone...
Hi,
I am developing application on NRF52840 with Zepyr 2.1.2 SDK, and I found two problems when using the example scan_adv, as follows:
Executing bt_le_scan_start in...
My team is developing for an nrf52840 on a custom design pre-production PCBA. Up till now we have been using nrf52840dk_nrf52840 in the"Board" field of the "Add Build Configuration...
Hi Team We’re using Nordic connect sdk 1.9.1 We’ve created a vendor service and defined multiple characteristics in same, We are using Nrf connect mobile app to fetch the...
Hi,
I am trying to capture provision packets from the BLE Mesh. I have nRF app for iOS. My iPhone is considered as a provision device, is it possible to provison another...
We are using SDK v1.9.1 with VS Code to develop software for a custom BLE board using the nrf5340 SoC. We also have/use a nrf5340-DK development board.
We generally update...
I want to make a card according to the NTAG213 specification package of NXP.
After I set the parameters, the default value for reading the card content will be NTAG203...
Hi,
We are running Zephyr 2.4 via PlatformIO on a nRF52840 based product. While spamming the nRF with a ton of BLE packets, after about 15 minutes or so we get the following...
Hi,
I have quite demanding SPI device which should send its data over BLE. Thanks to throughput example i was able to achieve maximum transfer speeds for synthetic tests...
Here are some values I got from the terminal:
11011110000000000001000000000010
00000010000001010000010000000011
00000011000000010000001011011110
I do not see the sign...
Good morning,
To my knowledge, the nRF52833 dk as well as the reference designs are FCC certified.
I'm currently searching the FCC IDs for these designs but I'm not able...
Hi
Using nRF52DK + SDK17.1 + S112
I have retarget enabled & using printf to output over UART (no DMA)
What's the best way to check if printf is busy outputting data...
Hi ,
What I am trying:-
-connect the custom board with nrf52840 chip using nrf52 dongle on pc with python.
-Already set some commands on custom board so when my pc ...
Hi:
i use the application note nA34's python file (dtm.py) to perform DTM PER test among 2 nRf52840 DK.
and in the LE_Test_Setup command ( the only set command which upper...
