Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
I have to make a connection from a central_uart to 4 periperal_uart every 60ms Sending 30 byte .
I Have to make a polling of all the peripheral every 60ms.
I know that...
Device: nRF52811
Board: custom (EYSNSNZWW module is used)
SDK: 16.0.0
SoftDevice: S112(v7.0.1)
Sample Project: ble_app_uart
Hello,
Is it possible to read BD...
I have a custom board based on nRF52840 with some custom peripherals : LEDs, buzzer, buttons, etc
To get my app working I copied the nrf52840dk_nrf52840 board from the 1...
Hi,
I started using the Nrf5340-DK with the openthread cli sample. It works fine, and now I'd like to move the main UART to pins P0.24 and P0.26.
To do so, I created...
Hello, I've been trying to migrate my code which uses NRFX SPI functions to NCS 2.0
The code compiles just fine on NCS 1.9, but after migrating to NCS 2.0 I noticed that...
I have just been hired to this company and they have assigned me to repair some of their defective modules. The modules are BL651 with what I believe to be nrf52810 processor...
Hi,
is there a driver available for the VM3011 microphone that comes with the Thingy:53?
The chip has some power-saving and wakeup features that are configured using I2C...
Hi,
We are having some issues communicating with a Winbond W25Q64 flash memory. Using the standard SPI Zephyr drivers an attempt to get the Manufacturer ID returns 0xDC...
Hey!
I am working on a zigbee asset tracking system for my thesis. Got myself 3 nrf5340 boards and a sniffer.
Unfortunately i can't manage to get started with zigbee...
Hi everyone!
I have recently been trying to flash the 'blinky' zephyr sample to the nRF5340 Application Core on the R4D4 Control Board. I am yet to have any success, by...
Hi there
I'm using Asset tracker v2 as a base for my application with AWS, however I wanted the FOTA to download to external flash, as the Asset tracker application is large...
I'm using a nRF5340DK with nRF Connect SDK v1.9.0 with MCUBoot and want to upload firmware updates for the application core using mcumgr.
I use the hello_world sample in...
We are migrating from Modem firmware version 1.2.x to 1.3.x. Since it is now possible to enable LTE and NBIOT both using the following XSYSTEMMODE configuraton:
How does...
I'm trying to develop a Bluetooth mesh network with low power consumption.
Is the performance the same when comparing firmware using the nRF5 SDK for Mesh and firmware using...
Hi,
I am developing the nRF52833 DK with NCS v2.0. The goal of the application is continuously send temperature data (using health thermometer service). I am currently trying...
