The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
Hello,
I'm doing some current measurements on both the Thingy91 and the nRF9160DK and I'm seeing some weird behaviours. My setup is as follows:
First measure on the nRF9160DK...
Hi dear reader
I've read several threads on this issue, but none of them could help resolve my problem.
I've an application which currently is only starting some advertising...
i am using a custom board same as the https://devzone.nordicsemi.com/f/nordic-q-a/29195/nrf52810-custom-board
i edited pca10040e_s112.
it got stuck at sd_ble_gap_ppcp_set...
Battery free BLE solutions are exanpding (wiliot, nexite, atmosic etc). Is there a plan in Nordic to provide a low power chip that will support battery free (or at least ...
Hi, I test the TCP/IP AT command in 9160DK, I download the example Serial LTE modem,
I send the command as below picture.
but it reply as below
==================...
Hello,
Is there any special area where I can save custom MAC address for each device ?
Basically I need to assign unique name and MAC address which the DFU and application...
Hey Forum,
I am using the USB Composite Keyboard example using the standard Descriptor given in the example.
I am able to get all the keys on the Host with a small caveat...
Hi,
I'm trying to use the GNSS application for the nRF9160 to compare GPS antenna performance. There is a Linux utility, GPSMON, that I'm trying to use to display side by...
I use FDS to store some application data. I performing accelerated life testing that randomly power cycles the nRF52840 (on time 4 - 10 seconds) while a central device ( Android...
Hi,
I am trying to run the fat_fs example from zephyr samples on nrf52 development kit (nrf52832) but during building I've got following error :
That's my development...
I am working on UART example and serial port.
I got compile error and modified retarget.c line 99 with
#if defined(__SES_VERSION) && (__SES_VERSION >= 34000) && !defined...
Hi，
I have a circuit board, which is powered by the battery and runs the Bluetooth program. When the power is normally supplied, it runs well. Once the USB charges the battery...
Regarding the capacitive sensor driver with adc for nrf51 series, how am I supposed to wire my board for this to work?
https://infocenter.nordicsemi.com/index.jsp?topic...
I'm trying to follow this how to and unfortunately cannot make it past step one.
https://devzone.nordicsemi.com/guides/short-range-guides/b/software-development-kit/posts...
Hi,
I have a central that uses PM to connect to some peripherals.
If I connect to a peer (connection handle 0), and disconnect this device (e.g. by shutting it off). I...
