Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Hello !
I would like to use pin P0.12 as common gpio output and configure it on quite later phase in my SW.
I use nrf_gpio_cfg_output and set/clear for have relevant value...
Hi,
I'm working on central_uart and peripheral_uart examples. I want to get the rssi value and tx_power of all advertising packets from peripheral to central via bluetooth...
Hello Everybody,
If you're reading this, you're likely in the same boat as me and need to scale Nordic's build process in an environment that doesn't have access to west...
Dear, We are working on a project where we have to request and read out data from multiple (up to 50, but can split up to 8 per central device) BLE modules (BK3432_QFN32)...
Hi!
I am totally new with Segger, so this is an idiot's question:
When I open a sample project and want to check my settings using the
"Configure nRF connect SDK Project...
I can't seem to be able to activate the iBasis sim card.
I'm in Norway.
It gets passed the initial screen and says the it needs user data. It then pre-populates with the...
SDK Environment: nRF Connect SDK v1.8.0 Target: Decawave DWM1001-DEV. This uses the nRF52832
My application uses more than half the flash size of the nRF52832.
Using mcuboot...
Hi, I'm working on nRF9160 modem firmware update.
For Understanding SPM with secure and non-secure firmaware, I have used UARTE2(secure peripheral) into non-secure firmware...
Hi All,
I am trying to run two UARTS using LIBUARTE.
this is the relevant configuration:
#define NRF_LIBUARTE_ASYNC_WITH_APP_TIMER 1 #define NRF_LIBUARTE_DRV_UARTE0...
Hi Everyone,
sdk : nrf Connect v1.7.0
ide : VS code
I was trying out central_hr sample on nrf52840 dk. I have simulated hrs server in nrf Connect mobile application...
I notice that the fork sdk-zephyr https://github.com/nrfconnect/sdk-zephyr
is missing important errata updates for nRF82510
as it is using and outdated https://github...
Hi, I'm trying to use the pwm driver to turn off or on a dc motor (which the speed will variate via the pwm signal). I need to achieve a frequency between 20kHz and 100kHz...
Hello,
How can I configure for a GATT characteristic which type will be used.
Without defining it will be a byte array.
I'd like to configure for example an int16 number...
Hi,
I am using Win10, nRF Connect 3.9.0, programmer 2.0.0. and I get "no matching trait found" when trying to program the 9160 on my board. I have seen a few other questions...
