void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
I'm using bsdlib (v0.7.7) on nrf9160 without Zephyr. Our products are working fine in the field, but so far you need to specify the host by IP address. I'm trying to implement...
Hi,
Is it possible to join an existing mesh network with a provisioner made on Nrf52840 (s140) ?
I have used the provisioner example to make a provisioner which actually...
Hi everyone,
I am working on a project, currently developing on the nrf9160-dk board. And I want to enable AWS and AGPS together in my project. And once I've enabled them...
Hi.
I modified the fstorage example to create the project.
I split Flash into three areas as shown below.
*Flash Area(0x26000 ~ 0x2ffff) : Bootloader
*Flash Area(0x30000...
Hello Nordic team,
We are making our own custom project, and we are facing problems in implementing lower power modes.
Reading from the info center, when the DK Board...
When initializing two channels, enter scan mode。After the two channels are converted, the callback function will be entered，Read conversion results。However, the requirements...
Hello
I am following a beginners tutorial on youtube and trying to implement simplest possible example of reading an analog value.
I want to use the nrfx library to do...
Hello,
I am working on a project where I am using 8 ADC channels on the nRF52832. When I run the code the device seems to get ADC values that look correct. But, if I pause...
I have an out-of-tree driver. It has an I2C that is working but also GPIO that are only working with compatible = "gpio-leds" but not with the driver compatible = "st,vl53lx...
On the nRF52840 there were many pins specified as "low frequency I/O only." Does the nRF53 have this same restriction? I don't see mention of these pins in the nRF53 datasheet...
Hello, I am working on application with nRF52833. What is max load current of internal LDO between VDDH - VDD? VDDH is 5V (USB) and VDD is 3.3V. There isn't anything about...
Hi
I am not busy developing an new product with nRF52840.
I want to use the BLE functionality and started with the ble_app_hrs sample application.
I download the pca10056...
Hi everybody,
I am trying install and set up Wireshark, i am in this step:
this is my output:
I think trhe problem is because of pyserial isn't detected, i have...
Hi,
I purchased a BLE dongle with your 3rd party HolyIoT: mini Holyiot-nRF52840-USB-Dongle. It is recognised on Nordic Connect, but not Nordic Programmer (Err msg: DFU trigger...
