I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
I used C:\ncs\v2.6.1\zephyr\drivers\adc as an example for testing adc, the following code has been added to nrf9160dk_nrf9160_ns.overlay
I applied voltage to pins p0.13...
I'm trying to test the RGB led on the thingy53.
Using the sample: C:\ncs\v2.6.0\zephyr\samples\basic\rgb_led which gives errors about the devices error: '__device_dts_ord_DT_N_ALIAS_red_pwm_led_P_pwms_IDX_0_PH_ORD...
HI currently i am using nrf52840 s140 sdk ver 17.1.0 and have added buttonless dfu in the central uart application after running we got run time error and we followed the...
Hi,
I am migrating from nRF51 to nRF52810 and I am trying to set Debug because its not working in Keil5.
I use PCA10028 board and I am connecting my beacon to P20 port...
I have a nRF9160DK board that is used for development of a custom nRF9160 board. The hardware designers have assigned GPIO P0.27 to be a general purpose output pin. This pin...
NCS 2.3.0
nrf5340dk_nrf5340_ns -- problem is in non-secure domain for an app built with TFM.
I have this in my nrf5340dk_nrf5340_cpuapp_ns.overlay:
at compile time...
Hi, I'm currently getting familiar with mcuboot and DFU
First of all, thank you very much for the new Academy course that covers DFU!
If I understand correctly, to enter...
I am trying to get MCUBOOT working with project based on the Audio_DK base, where we need to do firmware update over UART/Serial interface.
I have added the following...
I am using nRF5 SDK v17.1.0.
Is it possible to connect a peripheral device by MAC address, and the device is advertising with a different UUID from the central device? ...
I am using LittleFS for an external NAND flash by using the KCONFIG option CONFIG_FILE_SYSTEM_LITTLEFS = y and managing the driver implementation manually. This has worked...
We have difficulties to get RTT prints from MCUBoot while performing DFU.
As far as I understand Segger RTT is reinitialized when booting Application and this might be the...
Hello! I am using nRF Connect SDK v2.6.0
I'm doing the firmware that will be applied to the custom device.
This device contains one button, to switch on/off the device...
I could use a little help tracking down a linker undefined reference error. I am using nRF Connect in VS Code
c:/ncs/toolchains/cf2149caf2/opt/zephyr-sdk/arm-zephyr-eabi...
1. HI currently i am using nrf52840 s140 sdk ver 17.1.0 i have integrted the secure boorloader /pca10056_ble sdk with central uart after merging i have faced run time error...
I started a project from an example and see that this constant is defined =n in the prj.conf. I am wondering what effect this define has? I can't find any definition with...