void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Here is a focused support ticket description for your actual issue:
Device: nRF5340 DK ( nrf5340dk_nrf5340_cpuapp ) SDK Version: nRF Connect SDK v2.5.1 Modem: Quectel...
Hello, I'm working with Power Profiler Kit II and i see that we can use a digital port. I would like to know what the electrical levels for a valid High and Low. I can't find...
Hello, Currently I am working with the nrf connect SDK version 2.8.0 with an nrf5340 SoC. There is no external flash memory. I am trying to build a bootloader with the serial...
I have created a Zephyr Snippet (derived from the cdc-acm-console sample).
I am unable to select it in the Build Configuration. It is listed in the dropbox where the sample...
Hi,
I previously had access to the nRF54L15 Early Access SDK and toolchain, and my local EA workspace has been lost. I need to rebuild my development environment for a project...
Hello,
I am currently implementing a Central device using the nRF52810 as part of a Gateway board.
I intend to connect the antenna via a U.FL connector . My current design...
Is it advisable to POT circuits using the nRF9151? If so, please advise of any precautions. The IOT product that I'm designing requires to be intrinsically safe. As such,...
Hello:
I am developing a board and shields based on nRF5340 (but this question is not really specific to nRF5340, it also applies to most other nRF5x chips). The main-board...
Dear Nordic Experts,
Hello,
i have defined a custom service containing a custom char. value in a peripheral according to https://github.com/NordicPlayground/nRF5x-custom...
Hello,
I am running into an issue when trying to use both GPIO and I2C peripherals on the same set of pins on an nRF54L15 board. I have an I2C bus configured on two pins...
I have two devices on TI CC2538 that having problems talking to the NRF52840 dongle.
The channel is channel 11
There are 8 devices using TI CC2538. Only two of them...
Hello,
I recently noticed that I may have an issue with our current design of PCB and firmware. We basically have created a datalogger using the nRF9160, and we take readings...
In the process of upgrading from SDKs 2.x to 3.x I either broke something or missed a step as the build process no longer produces a HEX file I can use for programming. My...
