Hi,
We are using the nrfconnect for thread and zigbee 3.2.
We have modelled our Bluetooth peripheral, running on the nrf52840, on the BLE UART example. It connects fine...
I have installed nrf-command-line-tools_10.24.2_amd64 and jLink_Linux_V794e_x86_64 on Ubuntu 22.04. I have also installed nrfconnect-5.0.2-x86_64 for desktop and the Toolchain...
In the past few months I got aware, that some, in my opinion simple questions, get marked with
"This comment is under review"
and then nothing happens. For weeks, even...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
Sorry if this is too off topic, I actually don't have any problem with my nrf52840 dongle, but the App I'm communicating with. But maybe someone of you has run into the same...
I have a very simple product which consists in a Xiao Nrf52840 board (which is FCC certified) wired to a 5v relay module. I was wondering if I would need additional FCC certification...
Hello everyone,
I trying to configure my MDBT50Q-U512k to use the ble_app_nus example. According to my board, I need change to uart pins defined in this example. Then, I...
Hello, I am trying to add GPS functionality to my program running on the Thingy:91. However, I can't find any examples except for the Asset Tracker, which seems overly complex...
Hi,
MCU - nRF52832
I am trying to understand the power consumed during the PaWR operation. I am referring to the steps explained here: I am getting the a similar graph...
We currently have several nRF52840-based devices deployed in the field, running firmware developed using the nRF5 SDK and utilizing the SoftDevice S140 for BLE functionality...
Hi Team, I am trying to see the PaWR PDUs in wireshark sniffer. I am using example periodic_adv_rsp from NCS v2.9.0. I am referring to the link for exploring. How can I see...
Dear Nordic company,
I am writting to you in order to get some information about buffer sizes in your aplication. I think, I am bale to modify buffer size and maximum...
I am designing an application using the nPM1100 and I would like to know if I can use the VSYS as a power supply pin for my other circuit.
Is VSYS supplied by the battery...
In the nrf_sniffer_ble.sh script, the block that checks for an active virtual environment uses the following line:
if [ ! -z " $VIRTUAL_ENV "];
Notice that...
Previously, I compiled and downloaded the radio_test example into two DK boards.
I then used the CLI to set the parameters for each board one as TX one as RX
On setting...
1. Can we use SIM other than iBasis to use nrf cloud?
2. My SIM does not have a PUK. How to proceed without entering it.
3. We need SIM too kit document for nrf9161. ...
We are using the nrf52840-based module in our product.
This module is already certified with BT SIG.
Do we still need to certify our product with BT SIG certification...
Hi, As I am working on nRF5340dk and I am facing issues with flash memory. My application is exceeding the size of flash in nrf5340 (1MB flash). I want to move to nrf54 series...
This is a continuation of my previous thread ( Connections drop and don't come back (and "SoftDevice Controller ASSERT: 53, 296") ) (Case ID: 341823).
The project is a star...
Hello,
I am using Zephyr Toolchain v2.9.0 on an nRF9161 custom board . I have updated the modem firmware to mfw-nr+_nrf91x1_1.0.2 and flashed the board with the hello_dect...
