HI,
I am using the NCS V2.9.0 ,nrf Desktop sample;
I want to mouse can pair 3 hosts, and i can select one of them connect and work;
I set CONFIG_BT_MAX_PAIRED=3 and...
I have a custom nRF52832 board with outputs on P0.07 P0.08 P0.09 P0.10 and I want to write to them. 7&8 are working ok but 9&10 are not.
Let me emphasise THE BOARD IS WORKING...
Dear Nordic and community,
I am currently in pre-production phase of designing a PCB based on the NRF9151, and I am a bit confused by the Hardware Device Guidelines, which...
Hi Nordic engineer
I am evaluating a project based on nRF52840 and there is a question need to be confirm before schematic design start.
Due to limitation of power resource...
Hello everyone,
I'm trying to set up the Wifi stack on the nRF7002 and use it with MicroPython, but encountering a lot of difficulty with it. I cropped up a network_wlan...
Hi all,
I have a custom board build with an nRF9151. I'm able to connect on int with USB/UART, I can send and receive AT command. Right now I'd like to send certificat to...
Hello, I'm developing a BLE Central application using the nRF52 SDK. The central connects to multiple peripheral devices (nRF52832), each sending 6-byte ADXL345 accelerometer...
Hello,
I am trying to find a simple example of how to setup and run the SAADC on the nrf5340 in continous mode.
I would like to use the internal timer and only need to...
ZBOSS NCP: ZBOSS NCP Serial Protocol, Version 1.5 states that a "Full featured Zigbee PRO r22 platform is provided".
Is a more recent version of this document available...
The broadcast interval is 2s, and the power consumption is 7ua on the DK board; On this basis, the power consumption when using an external low-speed crystal oscillator is...
Hi,
when DC/DC is enabled, current consumption in sleep is higher than when using LDO.
This is consumtion with DCDC = 0
This is power consumtion when DCDC =...
Hi,
I am struggling getting my production programming script to work in a way where I get everything programmed including the App being validated...
For some reason it...
Hi,
I have tried the BLE image transfer demo and I really want to have the similar function about the real time data rate calculation. How could I do that? I found there...
Hi,
We are using nRF52840DK. Our main object is to collect the log for the BLE. We have installed the nRF Sniffer software and wireshark tool to extract the BLE Packets...
Hi,
We are using nrf52840 QFAA with our amplifier that gives ADC values at 100hz. We need to process the data via low pass, band pass filters, median filter, moving average...
Hi, i am using nrf5340 which has flash memory of 1MB. but my application is exceeding this memory size. what I want to do is to merge the image 0 and image and make it as...
Hello everyone I am gradually learning Bluetooth, it takes time, but I need a temporary solution, I need a so-called adapter, Bluetooth <-> UART, to simply transfer bytes...
Hi all,
I develop my own IoT board using NRF52840-QFAA (Rev3), I am follow the Intermediated Course about Creating custom board but some how my board cannot run blinky example...
With a npm1300 I'm able to charge (for instance, the LED showing charging status is on, BCHGCHARGESTATUS is reporting the different steps..... ) but the battery current reporting...
Hello
When following the guidline of a new way to extend boards , VSCode "Add Build Configuration" is blank. Am I doing something wrong or this is not yet supported by...
Hello,
Our company makes module using nRF52840. And we also make development kit with it.
I recently programmed open bootloader built-in hex in nRF5 SDK v17.1.0 (examples...
nrfConnectSDK V2.8
Toolchain
Board: nrf5340dk
Hi, while compiling ncs-spi-master-slave-example , I am getting below errors
In function 'spi_init': C:/Users/hello...
