Hi,
I am working on a project which has external flash (FM25V01A ) connected to nrf52832 board over SPI. And when building the project, I am getting the following error...
On the nRF51, LO leakage was measured when in receive mode. For 2402~2480mhz, LO leakage was measured at approximately 2745~2836mhz. The nRF52 does not measure LO leakage...
Hello,
I am experiencing difficulties connecting my NRF52840 board to the nRF Connect software. Despite multiple attempts, the board does not appear to be recognized by...
I try to migrate a working code from nRF52832 to nRF5340 with the use of 7002 companion chip for the network part (BLE). However, while I can jump to main and successfully...
I am using MX25 external flash with nRF9160. I am unable to find the configuration to use the Zephyr APIs to access the flash. I am able to access it when I am using
spi_write_dt...
Hi
I tried to run the sample "hci_pwr_ctrl" from the NCS v2.7.0 on the nRF54L15.
After starting the sample, the modification of the TX power level during the advertising...
I'm using the nordic ppk II to measure the power consumption of my device.
In order to validate the charge (current integral) displayed by the PPK2 i put two PPK2 daisy...
when i use vscode to open nrfconnect,it's always waiting there and can't start.as the same time,i can't open vscode by nrf connect for desktop,it will report the error ,but...
I am using ESB communication.
In general situations, data transmission works well. However, issues arise when multiple PTX devices transmit simultaneously.
It's understandable...
Hello,
I use Nrf52833DK running nRF Connect SDK (NCS)
I want read and write BLE MAC device address no matter it's the public one or static one.
Now i know bt_read_static_addr...
hello,
I'm try to fit my application to Android 14.
my application implement nordic DFU library ( for nrf52833 running freeRTOS firmware SDK 16 ) version 2.5.0
while...
Hi
I'm using the PDM module to capture audio through MP34DB02 PDM microphone ( here 's the datasheet). I set the clock frequency to default 1.032 MHz and a gain of +4 dB...
Hi there,
The nrf5340_audio application provides a -DFILE_ SUFFIX=fota overlay that adds FOTA capabilities to the application. This FOTA is introduced via Sysbuild configuration...
Hi, I've installed Visual Studio 1.90.2 + nRF Connect for VS Code Extension Pack v2023.11.3 + v2.6.1 toolchains + v2.7.0-rc2 SDK. Then I create a new application, copy a sample...
Hi,
I have tried the led strip example program and it works. My project will use 88 WS2812B RGB LEDs. For testing I used only 5 WS812B RGB LEDs. If I want to turn on red...
So I was experimenting with the Hardware Codec and I created a simple config which redirects the audio coming from the LINE IN mic to HEADPHONE OUT speakers.
Here's the...
We used the ADC nrf52832 to collect the reference source voltage, 1.240V. It is found that the consistency of each power-on is not good, for example, sometimes it is 2806...
Hi,
I'm running some transceiver tests to look at extended broadcast and ISO transfer modes. I am using nrf5340_audio_dk and ncs V2.6.0 to run nrf5340_audio application...
When testing the power consumption of the product with main IC 52832, we found that under the condition of 0dBm 1000ms, the peak current of beacon with PPK2 is about 15mA...
Hi, For the Adafruit Feather nRF52840 board I cannot find any information about the RTC. On the Feather board the 32kHz crystal is connected to the RTC clock input (P0.00...
Hi
I want to migrate my application to Zephyr RTOS platform from old setup given below.
Old Setup: Hardware: nRF52832 board. Soft device: S132 Software: SEGGER Embedded...