Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
I am developing a BLE mouse that can connect to 3 devices using nRF52840.
The sample code (peripheral_hids_mouse) allows simultaneous connection to multiple centrals....
Hello Team, We are currently building a circuit using nRF52840 CKAA (WLCSP -94) .We have configured P1.03 & P1.05 GPIO pins as UART_TX & RX . Kindly confirm if this pin or...
Hello, I am currently developing on the nRF54H20DK, which i have previously used v3.2.0-preview1 for. Everything works fine on v3.2.0-preview1. I have tried bumping to v3...
I am using the zephyr\samples\subsys\nvs example. By default the program stores data in internal flash in storage_partition. I would like to create a custom board file for...
I am using the peripheral_uart example. Now, our device tree seems to have crashed. Before the crash, I added the following configurations to prj.conf of the application core...
Hello,
I'm having some issues with the channel sounding on the nRF54L15. I'm using two nRF54L15-dk and two custom bords with the nRF54L15.I'm using SDK v3.0.2 for my software...
I’m trying to debug an existing product by opening its old firmware project on a new PC. The project uses nRF5 SDK for Mesh v2.1.1 , SoftDevice S132 , and nRF52832 .
I installed...
I am currently working in project with nrf54l15dk and 3.0.2 sdk. I'm trying to work with peripherals and I want my project to do the following: -Have 2 PWM outputs that used...
Hi DevZone Community
I'm trying to get a simple Hello World sample to run on an nRF5340DK board with a 2.8" ILI9341 based TFT display that has Arduino headers attached ...
Hello,
Im currently in the process of integrating Memfault OTA on the nRF9151 DK. My project has multiple boards: nRF9151 DK connects with nRF52840 DK via UART for communication...
Hi!
I am using the nRF52832 for a small custom PCB for a wearable device and I would appreciate a review from the experts, before proceeding with manufacturing :)
The...
Hi,
I have a FAT file system that I use with an USB Mass Storage feature. I use the mx25r64 NOR flash (the same as the nrf7002dk evalboard). I am working on ncs 3.0.2. ...
TLDR:
I'm working on getting LE Audio working on a Raspberry Pi CM4 setup and running into some frustrating issues. I've got a u-blox NORA-B126 module (with the nRF5340...
Hi nordic engineer
I have a product use nrf52832. And have two project,project use nrf5 17.0.0 SDK and MDK.
The project A choose chip nrf52832 and S132
The project B...
Hi
The nRF54L15-DK suite tests the accuracy of channel sounding, all ncs versions are v3.1.1. I am using the channel_sounding_ras_initiator and channel_sounding_ras_reflector...
