Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi Nordic.
I am developing with nRF52832DK and SDK 17.1.0
And it's connected with my Qualcomm board.
I want check GPIO input interrupt and output settings.
But...
Is it possible to view RTT console outputs in vscode during a debug session? I would like to see RTT console outputs right from the start, e.g. from bootloader, preferably...
Hi,
While using LE Audio, would it be possible to choose the data rate from 125kbps, 500kbps, 1Mbps, or 2Mbps?
nRF52 series do not support 500k coded PHY, so I would...
Dear support,
In NCS 2.1.2, it looks like download_client.c:socket_recv() is returning an erroneous unsigned type size_t , considering that it can can return either -1 or...
Hi,
I have late start issue on advertisement.
I have two device mode and we switch between when we want to. Device starts with Mode_1 with BLE enable.
When I switch...
Hi DevZone,
I am working on an application using:
nRF52840
FreeRTOS v10.0.0.0
nRF SDK v17.1.0
S140 v7.2.0
My question is if it is possible to enable the S140...
Hi,
With the nRF5340 DK boards (PCA10095), there are 3 VCOM ports (as viewed in VS Code) - printk debug logs for the app core are transmitted on VCOM2. However, the nRF5340...
hello to all,
I need to insert two CAN ports on the spi3 port of the nrf52840 with two different chip select and interrupt.
I have created an overlay file that defines...
Hello,
We have completed our custom board with nRF52810 and nRf52832, as asked in earlier questions needed SWD and SWDIO pins to upload code in SoCs.
So could you suggest...
Hi,
I recently found that the 5340 has a slow startup time on my custom nRF5340 based hardware, it takes about 3 seconds from power-on to the Main code running.
I did...
I use SDK17.10, when I send radio data using the esb，At this time, insert the usb, it takes a long time to enumerate the usb successfully; when I disable the esb,I plugged...
I'm trying to make use of the Async UART API with an nRF9160dk using NCS v2.1.2. As a starter application, I'm using the lpuart sample in nrf/samples/peripheral/lpuart. I...
recived error code 4
I am using nrf52840 for my application and use ble_app_template_pca10056_s140 for my project and receives error code 4 for nrf_sdh_ble_enable
Hi all,
I am trying to perform a FOTA upgrade over BLE with an nRF52832.
I started with the zephyr sample "peripheral_dis" at zephyr/samples/bluetooth, and then followed...
Hello,
please I have to build a container for these two PCBA:
https://www.nordicsemi.com/Products/Development-hardware/nrf9160-dk
https://developer.nordicsemi.com/nRF_Connect_SDK...
