Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
i try to build simple hello world program in c++. it successfully compile just yesterday, but somehow it fail to compile now. on the log it seem to use /usr/bin/c++ to compile...
The following code snippets produces Error code 0x0005 when trying to update a characteristic value via custom characteristic programming nd connected to nRFConnect app: ...
The nRF52833 datasheet lists a number of pads as "N.C." however I could not find anything in the datasheet about what to do with these pads. Is it safe to route traces over...
hi
I would like to use BLE Mesh to control my products. I would like to build a mesh network in advance, install a provisioner and automatically provision the nodes when...
I'm working with a lwm2m client using t he LwM2M client utils library to connect with a lwm2m leshan server.
Everything works great with LIFETIME = 30sec (default setting...
Hi:
There are two BLE architecture can be used on the nRF5340:
Split the Bluetooth LE Controller and the host part of the Bluetooth LE stack and run them on different...
Hallo Team,
I am using nrf45340 Audio DK to evaluate Bluetooth LE Audio application example.
For experimental purpose, I am using SBC codec. I have been following instructions...
Hello Nordic support:
We encountered a problem when downlaod the firmware for the nRF9160 with jlink nrfjprog program. Most our nRF9160 module can download firmware OK just...
Hi Nordic Team,
Working Environment:
nRF52832 DK, nRF17.1.0 SDK, Keil uVision 5 IDE, Windowns10 pro PC.
I am working on ble_app_uart.c Peripheral example.
According...
Hello,
the git version in ncs\toolchains\v2.0.0 isgit version 2.26.2.windows.1!
That prevets me from using git credental-manager-core in nRF Connect 2.0.0 console in Visual...
Similar to t_m's post here (only in a different SDK), I am trying to generate two PWM signals (motor1_fwd_pwm & motor2_fwd_pwm) in 180 degrees phase shift in respect to each...
Hi,
We have developed the firmware code for a system using nRF52832. We would like to keep the same system but switch the SoC to either the nRF52840, nRF52820, or nRF52833...
Hi there,
I am trying out the nRF Connect SDK v1.9.1 with a custom board (with an nRF52833) that we have produced. I have set up the necessary plugins in VSCode (v1.67.2...
I have two boards, a Thingy91 with "nrf9160 SICA B0 1924AP" and a nrf9160dk with "nrf9160 SICA B1 2110AM". Everything works as expected on nrf9160dk but on the Thingy91 shell...
