Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Intro We are using the nRF9160 with sensors we manufacture. The code developed is based on the serial SLM sample, toolchain v1.6.0. I am trying to keep the code/project files...
Hello. I have an issue with my development board. When attempting to recover the board, i cannot due to access port protection. This is the specific error message from the...
I'm new to developing nRF devices. This is the first time to set up SDK.
I installed Toolchain Manager v1.2.6 to install SDK, but it is too slow and falls into error. It...
am trying to mount little fs example with my external flash winbond w25q256 but my nrf52840 board taking internal memory and am using qspi
it get automount and writing in...
Hi Nordic,
I need to build an Auracast broadcast speaker (LE Audio BIS broadcaster). Besides audio, I also need two-way data exchange between the Auracast source and the...
Hello,
I am trying to have my own BLE advertising and scanning (with filtering) custom service (from now on peer service) in parallel with BLE mesh. So far I've been able...
Dear Nordic Team,
I have to use PSA Crypto key derivation in my NRF54L15 firmware during BLE communication with BLE Central, however, I am experiencing a problem when I...
In the function mentioned above, I repeatedly perform the following operations in a loop at a specified interval:
Power on the internet module
Connect to Wi-Fi...
I am trying to program modem keys using pylink and Modem_Shell with RTT enabled and it is almost working.
I find that the maximum download size for a command that I send...
Hi,
I got strange behavior of the SPI4 nrfx driver on nRF5340 (using nRF SDK v2.6.1 non-secure build with BLE enabled on NET core). Namely, every time I try to receive bytes...
Hello DevZone,
Our team has been working on a customized firmware solution that has been flashed onto the nRF52840 Dongle to meet specific requirements.
Usually, DK is...
In pm_handler_secure_on_connection, I see that it only looks for BLE_GAP_EVT_CONNECTED events if PM_HANDLER_SEC_DELAY_MS is not in use. I also see the comment "In normal circumstances...
The power domains for the nRF70002 aren't very clearly documented in the product specifications, so we're not entirely clear on how we should be connecting the VBAT pin. ...
Hi Everyone,
We are developing a custom retail display solution based on the nRF52810 SoC .
Currently, we are facing an issue where BLE advertising does not start properly...
When my device receives data from the Xiaomi Zigbee switch, sometimes it reboots without any logs.
(Note: Normally, when there’s a bug, the device pushes logs to UART, but...
