Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hi,
What all the parameters should store in non volatile memory for BLE operations?. Does specification mandates some parameters should load in controller?. What are different...
Based on documentation included in http://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/ug_nrf52.html#fota-upgrades I am attempting to get DFU working on the following...
I've got several problems but they are all linked more or less with the power profiler.
All devices I have are nRF52840 dk. The code is written with Zephyr but I doubt it...
Hi Everyone We are using nrf52840 for our custom PCB along with QSPI memory. We are using W25Q128FV as our qspi memory chip.
This function mentioned below is used to initlaize...
Hi,
I want to read and write the data from IS25LP064A NOR flash with QSPI. I am using the QSPI example from SDK v16. Please let me know how to get started with QSPI in order...
Hi,
I am wanting some information about any guarantees on the ordering of queued notifications and indications. According to https://devzone.nordicsemi.com/f/nordic-q-a...
SoC nrf52840, nrf connect SDK v1.4.2
we have a board with 3 sensors connected with independent SPI interfaces. after porting the code to ncs v1.4.2 from v1.2.0 the SPI communication...
Hi ...
I am getting the occasional error NRFX_TWI_EVT_BUS_ERROR being reported from the twi_irq_handler()
You can see in the following code snippet from this function...
I am using SDK17, nRF52840 based custom board and SoftDevice 7.2.0 with SES.
I want to use SDK's secure bootloader (pca10056_s140_ble) with my own keys.
To enter to...
Hi,
I have used a Custom board using nrf52832. It follows some procedures. After that, it needs to get into sleep mode for a time which was sent from the app
I use the SEGGER Embedded Studio for ARM IDE to build a clean build directory. From the IDE I can build the project and it completes successfully.
So I then take the same...
We have a product that uses a module containing NR52832 and also both 32kHz and 32MHz crystals. This has been operating correctly and is in full scale production.
On our...
Hi,
I'm having some difficulty debugging an issue with the mqtt library on the nrf9160dk.
I have written my own Cmqtt library class that wraps the Zephyr mqtt library...
