I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hi I am using the latest SDK for Mesh and also the latest nrf sdk. Downloaded and installed both last week. I have written an application that is derived from the light_switch...
Folks,
We are working on a custom design where the STM32L4 (external host MCU) talks to the nRF9160 over an UART connection to transmit sensor data. When the sensor data...
Hi,
I'm use nrf52840 with Light switch example of nRF5 SDK for Mesh v5.0.0 . Could I modify the packet of network layer ?
I want to add 2 bytes of UUID in the packet...
Hi, I want to add compression libraries like lz4 and audio compression to my zephyr projects. I am struggling to find good guides on how to add external/third party libraries...
Hi,
I have a nrf52810 board working as a peripheral, I want my board to connect to specific central application to protect it with malicious attack by other devices.
Please...
An error occurs when you run the following program(main.c).
[1;33m<wrn> bt_hci_core: opcode 0x2006 status 0x01 [1;31m<err> LOG_MODULE_NAME: Advertising start (err -5)
...
In the nrfConnect SDK I can see just one example for a I2C sensor - BH1749
I want to modify this for other I2C sensors.
However the README does not explain how to make...
I would like to calculate how much time my device does fast advertise and how much time it does slow advertising?
Is there a way to check this in python script?
Hi,
The SUPL Client library version 0.6.1 still links to the old BSD Libary, and will give a link failure, when building any application with SUPL Support
CMakeLists.txt...
Hello,
I am working to verify custom services on my device using nRF52 dev kit.
I am using HR collector example code as reference. I am able to read the custom service...
Hi,
I am trying to add the beacon Eddystone features to my DFU buttonless application.
After compiling the code, I wrote the softdevice, the bootloader and the application...
I am integrating a sensor on SPI 1 with cellular but device get stuck in CPU idle when first transaction of SPI is made?
I am using nrf9160dk_nrf9160ns as board configuration...
Starting with the dev kit, where I get correct behavior. First, I make sure the RESETREAS register is all zeros. I do this like so: NRF_POWER->RESETREAS = 0xFFFFFFFF; while...
Hello,
I am using nrf9160 and want to test the just simple SPI function. The code that I found from github( https://github.com/Rallare/fw-nrfconnect-nrf/tree/nrf9160_samples...
Is there a way to set duty cycle before app_pwm_enable(&PWM1) call ?
Or some other simple way to switch on and off a passive buzzer signal without every time at off/on cycle...
