Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
I would like to source a compact BLE board to act as a lock controller developed with with a matching transceiver for use in a fob and an app.
It would toggle the pio and...
Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
In order to send an SMS in PDU mode, I need a Service Center Address. Normally, you can find it via AT+CSCA, but this does not seem to be supported on modem firmware v1.0...
I have a central device (nRF52832/Soft device s132) that connects to two peripherals. Both peripherals send data to the central via NUS. I have incorporated the required changes...
hi guys , I'm trying to use the ble mesh protocoll for my master thesis. I need to send a message always when an interrupt on a gpio pin occur.
there's a problem beetwen...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
chip: 52832 . sdk 12.3\examples\ble_central\ble_app_uart_c\pca10040\s132,
i use this example to scan ble advistisment, i want to write some date to flash, i use flash_word_write...
Hi
I am doing a mesh application with :
--SOC:52832;
--with an AT Command Module connected UART;
--Mesh SDK :3.2;
--SDK 15.3;
in order to manage call backs from...
I built ...\examples\dfu\bootloader_secure\secure_dfu.eww ,pass,then when download to PCA10040 board to debug,but it show error" ELF/DWARF Error: Unsupported .debug_info format...
I am running custom firmware on a custom board using an nRF52832 chip. I have encountered an issue after migrating my project from SDK 14.2 to SDK 15.3. The issue is that...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
Hello,
Since I migrated from SDK 13 to SDK 15.3 I can not see anymore print of NRF_LOG_DEBUG, NRF_LOG_INFO, NRF_LOG_ERROR and so on, on segger Jlink Viewer.
I have tried...
Are the following arguments correct?
data_rate <RADIO_MODE_MODE_Ble_1Mbit> or <RADIO_MODE_MODE_Ble_2Mbit> and so on.
output_power <RADIO_TXPOWER_TXPOWER_Pos4dBm> and...
Hello,
We are using the nRF52832 and 2G(GSM/GPRS) module to build up one IoT product. We got a disconnect between nRF52832 with other master instance(mobile phone APPs)...
Using Softdevice s140 v6.1.0 nRF5 SDK v15.2.0
I am trying to write to the flash, here are my read and write functions:
Two problems:
The write function does not...
Hi,
I've added an instance of the Generic Power OnOff Setup Server to an element and I can see it and all the models that it extends, i.e. (Power OnOff Server, DTT Server...