Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Hello everyone,
right now I have two BMD-340 Evaluation Kits which used nRF52840 module and I want to evaluate Bluetooth Long Range and Data Rate of this module. I used...
Hi
I saw a fail for RF-PHY/RCV/BV-29-C on nRF52840 DK.
But I also find it is a known issue as "Anomaly 172 Addendum".
In the nRF52840_Rev_1_Errata_v1.2.pdf, two workarounds...
Hi,
I'm working with the nrf52840-DK and using the nRF5 SDK v15.2.0 Stack version.
I´ve got a working program for my coordinator (C) and my end device (ED). The C establishes...
Hi
I have this code that works like a charm when the device is connected and I want it to leave the network.
But if the device is dead or disconnected and I want to remove...
Hi,
I know this is a license question and the default answer is "contact a lawyer if you don't understand the license". But this can hardly be the first time someone...
Hi,
I'm trying to connect nrf52840 to IOS 12.1.4 as a Braille display. Standard BLE HID is working well, but when I try to connect as a Braille Display ( Settings/General...
I am trying to connect and according to the spec sheet, there might be multiple pipestatusevents.
When I try to connect using different phones (with different Bluetooth...
Hi,
I'm using the light switch client example to test the Mesh App on iOS.
The PCA10040 board can be identified through Mesh App, but not be identified on our test board...
I am using nrf52810 chip without softdevice or bluetooth stack. I started to develop at November 2017 with Datasheet version v1.2. On 31. Januar 2019 Nordic released a newer...
Hello,
I have project for collecting temperature information from 15 pcs temperature sensor.
It is possible to create system with 16 pcs nRF52840.
one of them will be...
Hello,
I’m using two nrf52832 as servers sending 20 Byte data with 18 ms notification interval.
Notification Data:
[incremented uint8_t ] [19 byte data]
Client:...
Hi,
I'm working with the nrf/samples/nrf9160/at_client (@ tag v0.3.0) with a PCA10090 board.
I had a question about the response to the AT+CESQ command.
Specifically...
hi,
i am quite new with programming tools like the nordic thingy and i am currently trying to get some initial program running, i.e. the blinky example. i have a few questions...
