Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hello EveryOne
My button event handler is not being called. following is my code what can be the problem.
uint32_t err_code;
ble_stack_init();
timers_init...
i am working with eclipse. i want to create a binary file. after successfully creating the .elf file eclipse displays a make error saying region ram overflow by so and so...
Hello,
If I enable POFCON at 2.1V threshold in my S/W, build and download it in my target, and I turn on n51822 at VDD is 1.8V. That is, VDD is lower than POFCON threshold...
Hi ,
Could anybody share me the details on the time taken by the nRF51822 to comeout from reset state for the below reset input.
Wakeup from OFF mode reset
Pin...
Hi...
I started with S130 demo example code. Added a custom services . The problem I am having now is that after I connect ble_evt_dispatch isn't being called.
I have...
Hi, I have purchased a Nordic nRF51 and start to write my firmware using mbed OS compiler. As far as I can see the whole process was working perfectly. I could update the...
Hi,
I have a BLE peripheral with a custom service (using a different chipset). I'm working with S120 as a central, and attempting to read/write various characteristics...
I have previously bought a Evaluation kit, (now obsolete) and registered with it. I have also designed a new custom board with version 3 silicon, but I cannot download v8...
Hii...
Am working on S130 demo example. While going through the code i found that code is implemented in polling method. when i compared with s110 example i found that...
How to flash SoftDevice and Bootloader (OTA enabled) to nrf51822 by CMSIS-DAP programmer?
For instance: I did cmsis-dap programmer with mbed code form github.
Can I do that...
hi,
I am want to communicate with nr52 dongle via serial. The dongle periodically outputs data which I read.
The problem is that is the python connect in the middle...
I'm looking for the set of command line interface for the bluetooth nRF51 sniffer program, such as to list the device available for sniffing. for example the L + . and then...
In the system on low power mode , how and where to change the startup time t1V7 for 1V7 regulator and startup time t1V2 for 1V2 regulator for better power optimization. And...
