[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
Trying to migrate from SDK v2.7.0 to v2.8.0 and suddenly getting the build error
Based on other forum posts, I was able to track down more information using the <build target...
Hi, I just got two nRF52840 dongle and it works great as BLE sniffer.
I want to send continuous BLE data (not only advertising) packet and sniff packets between bonded devices...
Dear Nordic Team,
I am currently working with the nRF5340 DK and would like to know whether it is possible to read or retrieve the Network Core firmware version directly...
Hi,
I am using NCS 3.2.1 and nRF52840-DK's version 3.0.3.
I flashed 2 boards with the openthread/cli sample.
From the CLI on both boards, I issued the following commands...
I’m trying to transmit a payload of up to 2,450 bytes using CoAP over OpenThread. Before jumping into firmware development, I want to evaluate the feasibility of transmitting...
Hello DevZone,
I have some questions about nPM1300. I know that nPM1300 need a battery pack that already contains a PCM.
When the PCM activate the protection due to overdischarge...
Hi,
I'm using the nRF54L15 (custom board, nRF54L15 DK base) with NCS v3.1.0.
I have two UARTs:
uart30 — Shell/console (needs CONFIG_SHELL_BACKEND_SERIAL=y , which...
Hi,
I'm trying to use an nRF5340 Audio DK to communicate with another board via SPI. The voltage needs to be 1.8v. How do I configure my board to do this?
Hi,
We are using the nRF7002-DK board. I am using Zephyr samples/net/wifi/shell with no other external connection other than the j2 micro-usb connection to PC and with the...
Hi,
We're aware of the modem 2K TLS buffer limitation. It's causing us quite a bit of headache related to the device shadow.
Our application needs a number of config parameters...
Hello,
I am trying to access to two partitions of 2gb each on a micro SD card of 32gb.
I can access to one partition of 32gb in my micro sd card but as it is formatted...
I've been struggling with Thread connectivity on a custom PCB, powered by a MinewSemi ME54BS03 module (with IPEX connector)
I'm using an external 2.4GHz antenna and I'm...
Hi,
I am facing a power consumption issue with the nRF54L15 (BM15C SoC) in deep sleep (System OFF / low-power state). The measured current consumption is approximately 221...
Hi all,
Note that I am using a Fedora Workstation VM on VirtualBox for keeping everything clean. I pass the connected USB development board to the VM. I am trying to evaluate...
