Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hello.
I am considering using the UICR OTP to store device-specific identification information. My understanding is that when accessing this area from a Non-secure application...
Starting from NCS v3.2.0, up to the current NCS v3.2.2, I'm getting back -EIO when trying to use the I2C bus. In commit github.com/.../428ce9f27bc368f8023de98cdd494b060374962b...
Greetings,
We want to use the MCK of the I2S module as a clock output for an external device. For that, we need a freuqency of around 4,096MHz. ACLK originates from the...
HI
I am using the DTM example routine of NCS 3.2.1 and am currently testing the combination of nRF54L15 DK and nRF21540 EK. After flashing the original example routine to...
I’m using an nRF54L15 evaluation board obtained from a distributor and currently testing transmission and reception of large data chunks. I built a vender model and a custom...
General flow when the issue occurs:
1. buf is allocated on prep_pool in prep_write_cb: data -> buf = net_buf_alloc ( & prep_pool, K_NO_WAIT);
2. buf is put to prep_queue...
Hi everyone,
I am currently working on a project using the nRF54L05 and SE052F (from NXP).
I found this GitHub link: https://github.com/NXPPlugNTrust/nano-package/blob...
We are using an nRF52840 running SoftDevice Controller (SDC) in a custom Host + Controller architecture:
SDC runs on nRF52840 as the Bluetooth LE Controller.
Our...
Hi, I run Matter test TC_DefaultWarnings.py but failed the test, see below the last part of the logs:
******************************************************************...
Hello! I am trying to upload 120KB of data through 2 protocols: https and mqtt+tls. Both the cases have same configurations enabled in the context of wifi, net mgmt, network...
Hello, i'm trying to flash mfw-nr+_nrf91x1_2.0.0.zip on a thingy91 x. it doesnt work via nrfutil nrfutil device program --firmwaremfw-nr+_nrf91x1_2.0.0.zip THINGY91X_13A2EC8A4FC...
The examples for the Matter Light Bulb app and others contain pm_static_...yml files with sections that look like:
I cannot find "orig_span" in the Partition Manager documentation...
I was asked by Nordic tech support to create a new ticket, because ticket number 357092 had become a long a winding thread.
I need a simple utility I can offer to an end...
I am developing a project using nRF5340 to drive some peripherals. During debugging, I found that no matter how I executed the pull-up/pull-down commands, the p1.00 and p1...
I am using qt C++ to refactor the dfu master station, currently I have a problem, that is, I want to communicate with 52840 simulated com but failed, I initialize, you see...
