Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
[uart - Copy.rar](/a master _error.png ttachment/3cc01f5e2484d2b0f33e62befd3e6a62)
hello there
I am interfacing master nrf51 dk with nxp's slave lpc11u24
(1) my main...
Hello
I played with the mcuboot_recovery_entry bare metal dfu sample. I noticed that if I sign an application image with an invalid key (invalid on purpose), the firmware...
I have been reviewing the antenna section in the datasheet of the BLE audio SoC nRF5340. The datasheet mentions a single-ended antenna output (on-chip balun). Could you explain...
Hi,
When the firmware is run in debug mode (J-Link connected), the system always works correctly. BLE initializes properly, and all sensors function as expected.
When...
Hello, everyone. I am an undergraduate student majoring in Mechanical Engineering in South Korea.
I am currently working on a research project to develop a PPG sensor using...
Hi,
(I'm assuming that the main() function of an application is actually executed as a thread.) I can't find any clear documentation that describes how a thread can suspend...
Hello team,
I am trying to interface the AT45DB641E flash with the nrf54l15 on a custom board. I am using the SPI00 instance.
Below is the configuration I set in .overlay...
Hi Nordic team,
We are working on a design that includes more than 50 peripheral node devices, each capturing sensor data and sending it to a single central receiver. I...
Hi,
I'd like to know how to tune the internal capacitance from the 32MHz crystal.
Specifically, I refered to section 4.12.1.1 Using internal capacitors in the nRF5340...
I am using the nrf52840 in QFAA package, and the external DMIC example receives audio data through the PDM interface. I noticed that the official documentation mentions support...
Hello,
We have been testing/validating sQSPI on nRF54L15.
We tested the sQSPI on two versions of our nRF54L15DK (0.9.2 and 0.9.3).
We are using this sample app: https...
Hello. I have one question.
When configuring RAM with the nRF5 SDK + SoftDevice, if I get the following error: APP_RAM_START=0x20006000 --------------------------------...
Hi,
I'm trying to program the nRF52840 Dongle (PCA10059, 2.1.1, 2023.26). I modified the Bluetooth: Central UART sample to use USB instead of UART and built it for the dongle...
I need to use one IO port of the nrf52832. This IO can not only detect the ECG signal but also achieve system off wake-up. The ECG signal is a PWM signal with a duty cycle...
I managed to somehow semi-brick an nrf52840. I've all but got the system/project working and wrote some instructions on how to install VSC with the appropriate toolchain and...
We are using the NRFJPROG ver 10.24.2 (JLINK Commander ver 8.92) to connect with our NRF52840 target. It fails to connect, here is the log entries:
[2025-Dec-10 17:05:02...
