Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
Hi,
I'm testing maximum tx throughput.
I'm using ble_app_hrs example and mcu is nRF52832(s132). (sdk : 16.0.0)
The goal is transmit data at 96Kbps.
I read that the...
Dear Members,
We have 2 ANT receivers and 1 ANT Speed Transmitter, (Bicycle Speed Cadence) , Garmin GSC-10,
Is it possible ? Looks like one receiver gets a good value...
Hi,
I am using NCS v2.0.0, VScode with "nrf connect for vscode v2022.7.242".
I can't build any samples with MCUboot, by enable CONFIG_BOOTLOADER_MCUBOOT =y.
The build...
The following error occurs when I plug in the USB cable to burn the firmware，This is an interesting bug: it usually fails on the first burn, but succeeds on the second or...
Hi everyone,
I am new to nRF52833, and trying to learn it with some tutorials. I am following this tutorial.
You can download my "examples" file from here . You should...
Hi,
Can you please provide some sample code for sending data to Tm4C using ble_app_uart in VScode and also tell me which function I need to use for sending some data from...
When I use Windows nRF Connect to connect to nRF52832 device. It pop up window for user to enter passkey. But When I use iOS nRF Connect to connect to nRF52832 device. It...
HI, I am start use NRF52840DK(rev3) to devlopment usb application，but jlink always show this information
I try to use 'nrfjprog --recover' to disable read protection,...
Hello Groups,
I'm trying to send I2C/twi data from nRF52832 using the Nordic development board with nRF Connect SDK 1.9.1.
Based on the sample project ble_app_uart, I...
Hi nordic:
As shown in the figure below, I see that the BLE protocol standard mentions the ScanReq backoff mechanism. Does NORDIC implement it?
jermi.jin
thanks!!...
Hi,
The central_uart sample hardfaults when bt_enable(NULL) is entered. I can use the debugger and step over the first couple lines but stepping over bt_enable causes a...
Hi
I have integrated the example code for mesh dfu provided in the nrf mesh sdk5 in my main application . I have followed all the steps mentioned in this dfu guide. The...
Hi,
We have a working LwM2M device based on nRF9160 and NRF Connect SDK 1.1. When we run with a short register-update period (30 seconds) on a NB-IoT network it works. When...
Good Morning,
I would like disable passkey in the example "peripherals_hids_keyboard". I am able to connect with differents hosts (2 smarts and i computer) but I'm having...
