It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hello!
I am trying to write a program for controlling a servo motor. I got recommended a code for making a PWM signal by someone else from devzone, so I am using a modified...
Hello, I would like to know what is required of me to automatically create com port in windows that would allow me to use my ble device as if it were attached by ordinary...
Hi,
I want to receive some data in my nRF52832 from MATLAB over UART and send some other data from nRF52832 back to MATLAB. I need some bandwidth for data transfer from...
Dear support,
I am the beginner of of the Nordic with 52840 chipset, i am try to running sdk 1.90 with zephyr os
i am try to running this case : cfb
C:\Nordic\NCS...
Hi,
I'm trying to use two nRF52840DK as Zigbee routers. I have the following setup,
Software
Application: Home Assistant
SDK: nRF5 SDK for Thread and Zigbee v4.1...
I really like the flexibility that the CLI from FreeRTOS gives me for making my own commands. Does Nordic have a similar library available that I can just import easily into...
Hi,
since The image management provided by mcumgr is based on the image format defined by MCUboot, so does "nRF Connect android app DFU mode" use mcumgr libraries in it...
I'm developing an Ultra-Wide-Band indoor localization system consisting of beacons (stationary, hard powered) and tags (mobile, battery powered), and am looking for a suitable...
Hi Nordic,
I am developling a porject with nRF5 SDK 17.1.0, with nRF52832.
the 52832 serve as a central role.
1、I am wondering what is the difference between BLE_GAP_EVT_CONNECTED...
Values change rapidly and bt_gatt_notify_uuid is called at 10ms interval while bluetooth connection is set up for 15ms connection interval. I assumed this would simply queue...
I have attached all sleep modes of our controller that i found through forums and from your suggestions.
But my problem is No one of these sleep modes, wake-up through...
Hi,
I am just starting out creating a project to run on an nRF9160 on custom hardware. I have set up a development environment (v1.9.0) through nRF Connect for Desktop...
Hello I use nrf52840 and BME280. I plugged it GND GND SDA 45 (P1.13) SCL 47 (P1.15) VCC 32 (P1.00) I use timer to refresh data and on the first line of the code I init gpio...
Hi,
In the nRF52840 Product Specification 1.7 , page 34 chapter 4.4.1.9 INFO.VARIANT, I read that the hex code of variant "AAF0" is 0x4141 45 30. However the description...
Configuration :
IDE : SES V5.70a
SDK version : NRF5_SDK_17.1.0
Board : NRF52840DK
Hello,
I'd like to use 4 channels of the ADC in a scan mode at a high frequency...
