Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
Hello,
i am working with the Enhanced ShockBurst proprietary protocol and i am wondering where I can find the sources of this protocol, so that I can do some changes. ...
Hi as I can see many other also experienced problems installing nrfutil. I spent 5 hours trying Windows 8.1, Windows 10 and a Debian Linux box. I'm no python expert and I...
Hello,
I'm working on a project related to DWM1001-DEV at University of Illinois at Urbana-Champaign to build a demo of the product that uses UWB. However, I'm having several...
Good day
Please assist, I had my power profiler (PPK II)and Bluetooth dongle both plugged into my laptop. I accidentally upgraded the firmware for power profiler (PPK II...
Hi
I am using NRF5340dk with NCS version 1.5.0, I need to port the below library which was written for nrf51.
github.com/.../ADS1231
KIndly, Help me to resolve this...
I am using SDK nRF5_SDK_15.3.0_59ac345 with nrf32832. I want to write data from central to peripheral characteristics. I wrote below code:
Everything worked fine when...
I run the program step by step, when execute NRFX_IRQ_ENABLE(SAADC_IRQn);, it will go to app_error_fault_handler,.What's wrong ? I have do nothing with it!
I am trying to set a timer pulse at 500kHz and on every high pulse i want to do a read on another pin.
I have an IC HX711, that has a 24bit output MSB. every positive...
Hi,
im a beginner and i have problems to integrate the Homekit SDK in the Connect SDK.
Maybe anyone have a link to a tutorial?
The implementation by west has no effect...
Hi, Q1) I am facing an issue with the heap memory. I am using the Cjson_Parse function which uses quit a lot of memory. So I am wondering if there is a way to increase the...
Hello,
i m working on usbd example on nRF52
i have a problem that usbd stops sending data aftew few time. the port is still enabled but the data is not sent! any proposition...
I am trying to communicate with a sensor that has some interesting timing requirements for reading information from it, it requires ~100us delays between the address to read...
I want to calculate the power consumption used by many peripheral like GPIO, TWI, UART, SPI, RTC, SAADC. I can't find these information in nrf52840 PS v1.1
Because I don...
Hi, On my Windows 10 machine I've installed nRF Connect for Desktop (v3.7.0) and then used Toolchain Manager utility for installing nRF Connect SDK (v1.6.1). Afterward, navigating...
Hi,
I'm working on a project using BLE via s140, everything was working fine until I wanted to implement usb.
I created a blank project in order to validate the usbd then...
Hello, I have and audio source and i would need to divide it beetween two frequencies (<95Hz and >=95Hz).
Im trying this thing with a nRF52840 and i was looking at DSP libraries...
