I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Dear Developer Zone,
I am new to ANT and am looking for someone to help me to setup an example 15 channel (14 devices) ANT network using the S332 soft-device to test communication...
I am working on nRF54L15 and I want to store some user data in flash and for that I want to define the partitions.
I have selected the Target: nrf54l15dk/nrf54l15/cpuapp...
I am running smp_svr demo on my nrf54l15DK board, and use mcumgr command on my linux.
I could connect to my ble device and echo hello successfully (via peer_name='Zephyr...
Body:
Hello Nordic Team and Community,
I am working on a project using an nRF52840 chip on a custom breakout board . I am not using any pre-made development boards or...
During the testing phase of my device I use the Zephyr (uart) logging module and the Zephyr shell module(CONFIG_SHELL_LOG_BACKEND=y). Shell is mostly disabled, and is enabled...
I followed the migration guide for NCS 2.8.0 here for a custom board with engineering rev B silicon. After doing so I can't flash the board anymore and it gives me this error...
I am developing my product using the desktop app in the NCS SDK. I found that during OTA, it can only upgrade from a lower version to a higher version. This means that when...
I am using Keil v5 and the nRF5 SDK 17.1.0 .
I use this example.(nRF5_SDK_17.1.0_ddde560\examples\ble_peripheral\ble_app_uart\pca10040)
I hope the chip enter system off...
Hello,
We are using the nRF52840_CKAA_R7 package of the nRF52840 on our custom board. The board's USB pin connections are designed based on the nRF9160-DK's nRF52840 reference...
Hi,
I just received my Thingy91x. I followed the onboarding and created a provisioning profile in NRF Cloud. The device did not connect and no logs appeared in Serial terminal...
Hello everyone,
I am trying to execute Nordic Bluetooth ESL tutorial with PAwR. Here, I am able to change the images and handling the state of an LED connected at the Tag...
Hi,
We are encountering an issue where the existing firmware does not run on the chip when powered by a coin cell, even though a 3.3V power supply is available from the...
When I compiled and flashed the Nordic Distance Toolbox example onto two nrf5430dk boards without changing any options, the following message appeared on one of the UART ports...
Hi,
I have the following scenario:
nrf5340
SDK 2.1.1
HFCLK: 32Mhz crystal
LFCLK: square wave of 32768 Hz from an external RTC, range [0 - 1.8] Volts
square wave...
