It is good practice to prefix the includes from one's C libraries with a directory so that they are all part of the same 'include namespace'. Unfortunately the Nordic SDK...
Hi, is there an available developer in my tri-state area of Minnesota, N. Dakota, or S. Dakota? Please call me if you are available for a project for hire. The developer should...
I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well. ...
HW/SW Versions:
nrf52840 Dongle DK
nrf Connect SDK 2.5.2
Issue:
I'm developing a Zigbee device based on the ZBOSS, using an nrf52840 dongle development kit and there...
Hi,
Our custom hardware makes use of an external flash device, IS25LP032D-JTLE-TR, for storing files (littlefs) and OTA updates. We've noticed, seemingly only after a power...
Hi,
We have developed a nrf5340 custom board powered 1.8 V. So we cannot use the nordic DK board to program it.
I would like to know if there is an interface other than...
I have an application where I am using the SAADC to take ADC samples. At any point during the measurements, I want to be able to stop the samples prior to the ADC buffer filling...
Hi,
I trying to adapt the ble_app_multilink_central example to allow more than 8 peripheral connections to the central device. However, when I change NRF_SDH_BLE_TOTAL_LINK_COUNT...
Hi Everyone,
I am trying to develop a simple application with the XIAO BLE Sense device, the idea is to send a BLE message when something hits the device. To achieve this...
Hi,
I am using nRF52832 board and I want to understand the current consumption in the board will differs while running the code in zephyr RTOS platform and without zephyr...
Hi,
I would like to know where Matter's commissioning ad timeout is set.
I understand that it stops after 15 minutes, but I don't know where it is set.
Best regards...
I am currently learning nRF52840 , I started the BLE fundamentals course , and this the lesson 1 exercise , It Worked Fine , after the lesson 1 , none of the lesson's exercises...
Hello, I want to update the firmware(FOTA) of nrf5340 using AT Command of nrf9160.
I've already reviewed the content in the dev academy below https://academy.nordicsemi...
Hi,
I'm using nrf9160 MQTT at commands to send real-time data to the cloud. I run into the issue where the MQTT publish may fail (frequency varies around 1 out of 500 publishes...
Dear, I'm developing on nordic 52840 with ncs2.6.1.
I found that the Current will reach to 600+uA in k_sleep state by enable SPI in device_tree and if i disable the spi...
Generally, the peripheral calls the sd_power_system_off() function to enter power off mode. Then use GPIO interrupt to exit the power off mode and connect to the central device...
I was going through the driver files for CS47L63 and apparently I2C is not supported for some reason. Here is the code block I'm talking about
Is there any explicit reason...
Hello,
I've been encountering build issues when trying to include MCUboot as a bootloader for my nRF7002DK project using the Nordic Connect SDK version 2.5.2. Specifically...