Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hey, so we have been building a prototype similar to a hearing aid with the nRF5340 Audio DK. I had a few queries regarding the DSP block of CS47L63 Hardware Codec which is...
Hi,
I'm implementing a BLE GATT peripheral that has no display but it does have a button.
I'd like to make some characteristics only available to devices that are BONDED...
Hi,
I am using CJSON_LIB from nrf-sdk modules, I even tested this cjson lib in such a simple way in helloworld app (I attached the sample project.), and after running for...
Hi!
We're looking into possibility to use nRF5340 and nRF7002 to provide BLE and WiFi access to an external MCU. The idea is to use one of NXP's MCUs as the main processor...
In the Power Profiler, when I select a larger area in the data logger, then it stops updating the selection time. It works great till 16:40m, but then stays at this value...
I'm working with a DVK that has an nrF52840 with a Sierra Wireless HL7800 modem. The modem is connected physically to UART1 while the UART0 is used for the following as shown...
Hi,
We have developed our code against SDK 2.3.0 and I wanted to try to upgrade the SDK to 2.6.0. I had to remove CONFIG_OPENTHREAD_CHILD_SUPERVISION from my prj.conf, but...
HI
I basically define uart_init(); in Main.
And use DEBUG below to decide whether to use UART.
#ifndef DEBUG
NRF_UART0->TASKS_STOPRX= 1; NRF_UART0->ENABLE =...
In the transition from SDK v2.5.x to v2.6.x, Nordic removed support for boards that don't have the nonsecure (_ns) configuration in the Azure IOT hub sample. In other words...
Hi
I developing a nrf9160 project and try to use FOTA, I reference to example /samples/cellular/nrf_cloud_rest_fota.
finally firmware can successfully downloaded
...
I'm learning to use the Zephyr toolchain and in the interest of connecting the Zephyr-side coding to the i2c protocols I am familiar with, I have some questions.
I'm trying...
I have my software set up so that it does some computation within the Attribute write callback function like this.
b roadcastKeyHandler does somewhat of...
We designed a board based on the nRF52840, and are using nrf5 SDK 17.1.0 with S140 SoftDevice. The board has an RTC, LSM6DSO as IMU, an opamp front end for the analog inputs...
As title says, I have a clean install of Xubuntu 23.10, latest nrfutil and toolchain-manager package
My shell is zsh, however "nrfutil toolchain-manager launch --shell zsh...
I am looking at the "mesh_shell" example project. I was able to build the sample for nrf5340 dk this way:
- create a new build configuration for "nrf5340dk_nrf5340_cpuapp...