I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
I see that nordi is working on wifi 6 .
When It will be available and on which platform ?
Is possible to have presentation on wifi 6 versus wifi 5 and BLE ?
Best Regards...
Hi
I want to use a Nordic NRF52840 to sniff and dissect a Digimesh network. Digi do not provide a sniffer or/and dissector for their products. There is no promiscuous version...
hello,
we are trying to use the stack guard module - obviously we want this to give well-behaved fault handling in the event that the stack gets too close for comfort. ...
Hi, I have a few questions regarding the modem module of the nRF9160 and considerations that might to be made when developing for it:
1. How does the modem determine which...
Hi,
We upgrade our SLM app from sdk 1.9.1 to sdk 2.0.0 and now when we try to look for GPS there is a reduction at the voltage from 3.3 to 2
what are we missing? what...
Hello Team,
This ticket is in continuation with Case ID: 292116. Based on last discussion I have taken more modem traces which are present in the attachment. Please ignore...
I've been working on porting a project to NCS using VS Code as my IDE. Now that NSC v2.0.0 is out, I wanted to move to that. I found the migration guide: https://developer...
I want to intercept some data in the RX (in section UART_RX_READY in uart_cb() as a command with arguments. And I do not want this data to be sent on the the BLE.
After...
I use nRF Connect to scan BLE devices. nRF Connect can find ANCS2 device. But nrfutil dfu ble failed with Exception: Connection Failure - Device not found! And I can't find...
When I run TX tests with the AT%XRFTEST command, I can start the TX test without any problem but then the modem stops responding to AT commands. For example, if I send
...
Hello.
We are currently using MBEDTLS to handle DIFFIE HELMAN and AES . We have disabled all unused curves and modules, as suggested in documentation. Still the size of...
Dear all, I am trying to develop an application on Nordic nrf52840_dongle utilizing Bluetooth and Nordic Led Button Service. The application running on the dongle is supposed...
I was starting to develop for our own board based on the nRF9160 where we will just be using the LTE-M and while doing so, ran into issues with enabling the LTE. To do a sanity...
Working on a BBC microbit v2 (nRF52833) with Zephyr, I can only control the "ring" pins of the microbit's edge connector. I can setup pullup or pulldown on the other pins...
Hello,
I am using the nrf52832 and would like to know the clock sources used by the external peripherals. From the searches, I found that PCLK16M is used for most of the...
