Hello,
I have a device based on nRF51822 revision 2 and SoftDevice S110 v7.1.0. Because it is revision 2 it is affected by PAN44 and PAN45, and by default the SoftDevice...
Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Dear all,
The forum is full of questions around printing floating point numbers, however, I have a rather strange issue where maybe someone can help.
I have a project...
Hi,
I am new to creating project from scratch.
I want to use nRF51802 module. From few support tickets i have come to know that SDK version 12.3 and SoftDevice S130 version...
This is a beginner question and may well related to a misplaced setting in Segger Embedded Studio.
I am working towards a BLE scanner application which will include NFC...
Hi, Thank you for your attention to this matter.
Please provide nrf5340 layout in this package to me: WLCSP 4.39 x 3.994 mm package The customer needed to use this encapsulation...
I want to receive more than 250 bytes over NUS ,presently i have receiving All Data but in parts of 20 bytes (i.e after receiving 20 bytes BLE_NUS_EVT_RX_DATA event is occures...
Hi there,
I've recently purchased a nrf9160dk to evaluate. I've got some demo code going connecting via LTE and chatting to my AWS server via TCP and that's all going well...
Is there any SPI examples by directly accessing the registers?
Based on SDK15.0.2, for NRF52832 or NRF52810, higher freedom, higher memory utilization.
I want to know the best way to handle time-consuming processes.
I am using an external module used for AT commands via UART. It is necessary to judge the success or failure...
Hi,
Tools used for programming
I am trying to program my custom Adaruit nrf52832 board through NRF connect Programmer.
I am using Nordic nrf52DK to program Adafruit...
Hello,
I need to temporarily hardcode MBR_BOOTLOADER_ADDR address in the code so flash area is calculated correctly in fds.c. I have the following code in my ld file:
...
I'm having issue where after booting I can immediately do three SAADC samples as follows:
This works as expected where I get the callback immediately after the third call...
Hi Nordic,
I have decoded the advertise report below. Will you please confirm my understanding is correct.
Especially
[02] --> NUS_SERVICE_UUID_TYPE
[01] --> BLE_UUID_NUS_SERVICE...
Hello,
I am using the ble_app_beacon example on a nRF52840 dongle.
Without changing the code I am able to load and use it on my dongle.
Now, I am trying to add some...
Hi , i have attempted to build an spi read and write function for the BMI085 imu sensor and I seem to be having a problem with the read function. i have used the spi example...
Hi i'm studying ESB in nrf52833 DK
I have a few question.
1. When a packet is sent from ptx to prx, transaction starts, and when prx receives a packet from ptx, it sends...
