Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Hi,
I am working on a product based on an nRF52832.
For testing purposes, I have setup the Unity testing framework (using Ceedling).
As soon as a module I want to test...
Hi community ! I'm currently working on mesh, more precisely on nRF52840 device. I archieve to do everything i want with it (combine BLE NUS with MESH). Now, i want to know...
Dear All,
I am using the ble_app_template as my baseline. I have created a custom service with various characteristics and I am able to broadcast my service, connect and...
Our compliance engineers are failing the unmodulated FCC test for our radio because the signal only spans 1MHz, but needs to span 2MHz. We do not have this issue when using...
Hello all,
I'm working on a prototype for a device that simultaneously scans and advertises in certain cases. I have been able to do everything so far except scan by copying...
Hi
I am working with nrf52832 NORDIC soc with Segger with nrf52 sdk 16
I have looked at the "pin_change_int_pca_10040" example and tried to play with it a little bit...
Hi there,
I recently upgraded to nRF Connect for Desktop v3.3.3 and the programmer module to v1.4.2 and I am experiencing the following issues. At first, when I would try...
Hi,
Iam working on a nrf52840 and trying to achieve data flow from BLE device using NUS and transfer this data through UART.Uart is configured as (TX:P1.01,RX:P1.02).Iam...
I am using an nRF52 dev kit. I have loaded the pca_app_hts_pca10040_s132 example into the board. I only added these lines of code
nrf_gpio_cfg_output(ARDUINO_9_PIN); nrf_gpio_cfg_output...
Hi,
There are several new drivers under "nRF5_SDK_15.0.0_a53641a\components\drivers_ext\", but no example now.
I have setup the HTS221 driver and it works. I turn to...
I'm using nRF52-DK, and following the quidelines from devzone.nordicsemi.com/.../getting-started-with-nordics-secure-dfu-bootloader . I'm using the prebuild "blinky_pca10040...
Im trying to interface nRF52DK to Custome build acceleration sensor.
I want to use I2C communication. Are the pin connections mentioned below sufficient?
...
The buttonless_dfu_sdh_state_observer in this example is shutting down the cpu when the softdevice is disabled using an observer.
I'm not sure why this is necessary...
Hi everyone,
I have a project written in C++ for nRF52 series using the SDK 15.3.
If I use Keil and uVIsion, the project compiles and works great. With the same source...
