Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
Hi,
I modified the UART example to work on different pins i.e. pin 17 and 15 on custom board. When I use printf() to print logs, it works. If I use the NRF LOG to print...
Hello,
I am trying to build a small voltage stimulating probe for a research project I am doing. I was going to originally use the Rigado BMD-350 which includes the nRF52832...
Hello,
I am trying to connect my nRF52 DK to my phone (apologies not desktop) and perform a DFU OTA via the nRF Connect app. I'm using SD132 6.1.1, and uploaded the secure...
Hi,
I am using NRF52832 with softdevice s112 and SDK 15.3. I have 20 bytes of data which I want to retain in RAM during system off. I use the following code so that the...
It happens on a new board. It is possible that an HW problem occurs (Xtall), but how to debug it? How to know if Xtall correctly runs? The same code runs correctly on another...
hi ... i am using nRF52832 ,i want to save the battery so i am planning to use system off mode . how to wake up the device from system off mode using threshold value or either...
Hi,
I'm using the "pc-ble-driver-js" to implement a central on PC, trying to send a file through a Write w/o Response characteristic to a device. It's OK for a small file...
Hi ,
I am trying to merging 2 application hex files for example : usbd_pca10056.hex and ble_app_hts_pca10056_s140.hex using mergehex tool.
I could merge the hex files...
I am trying to use segger linker instead of gcc and followed the below link to port the changes
https://wiki.segger.com/Porting_from_GCC_to_SEGGER_Linker
I have tried...
Hello,
i was wondering if it is possible to have a node in a mesh, that is communicating to a PC via a COM-Port. I know it is possible to communicate via the J-Link Debugger...
I want to control network formation process for coordinator and end device through application layer. I refereed light switch example to understand network formation process...
Hi,
Please help, I've been struggling with this problem for a week and I want to get to the bottom of it.
I have production devices in the field based on s110 v7.1.0....
Hi,
Please help, I've been struggling with this problem for a week and I want to get to the bottom of it.
I have production devices in the field based on s110 v7.1.0....
Hello ! I encountered a problem in sending and receiving data from one nrf51 card to another nrf52 card
i use this method in (ble_config.c) to send string data :
void...
Using the nrfx_qspi driver, it is possible to put a QSPI memory into DPM to save power, this all works fine and well. We want to keep the memory in DPM when uninitiating the...
