Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
I'm trying to set PWR_UP bit to 1 for the device to go into standby-I mode using STM32F103RBT6 and HAL libraries.
I send (0x20 | 0x00) command (write_reg | config reg)...
I'm trying to compile the S332 example project ble_ant_app_hrm_pca10040_s332.uvprojx. I'm using the V12 SDK and Keil uVision V5. When I try to compile I get an error saying...
Starting with "Development with GCC and Eclipse", I've gotten "blinky" to run on my BLE400 with an nrf58122 using Eclipse Oxygen. I think I'm using SDK12.3 . I started with...
pca10040 S132 5.1.0
if i run only a single nrf nus service (rx and tx) at 4 k bytes / sec both directions, how much load would this put on the 52832
the test is assuming...
Hi,
I'm connecting two I2C modules : MAX30102 and MPU-9250
I can individually communicate with either of these modules and they work okay. But if I connect both of them...
Hi Nordic,
I noticed that both Write Without Response(write_wo_resp) and Write(write) can be enabled at the same time when add a characteristic. I know it means both types...
HI all:
If the iphone saved is English name i can parse it out, But if the save is a Chinese name I don't know what is to use the utf-8 encoding and unicode, who has successfully...
Hi，
i defined spis rx and tx buffer length at:
#define HUB_SPIS_RECV_BUFF_SIZE 1024
#define HUB_SPIS_SEND_BUFF_SIZE 1024
because the rx data length will be vary...
Hello nordic
I use ble to create custom services, I want to create an embedded system that can create and send and receive data. I am using sdk version 14.2.0 and what...
Hi,
Im currently designing a custom pcb using nrf52 reference design available here . In my design, I have to connect the ground of two analog signals to VSS of nrf52832...
I tried Blinky blank application on PCA10040 by IAR. By pressing "Download and debug", everything is fine, I added RTT debugging information and can see it from RTT viewer...
I Have an issue trying to flash a nrf52832 custom board.
Something extrange happens because when I download an example from keil that blink a led(gpiote_pca1036(nrf52 PCA10036...
We are using s110_nrf51_8.0.0_softdevice.hex soft device and nRF51 SDK v10.0. We have below questions in case of soft device assert scenario.
In what scenario's soft...
Hello,
I am working with the example of PDM example on the nRF52832.
And over this I would like to use the drv_speaker. I put all the files from the Thingy 52 example...
On a system using an NRF52832 with S132 softdevice (without no external LFCLK XTAL), in low power mode via sd_app_evt_wait() - we see a nominal current of ~3uA with a periodic...
