Ok so here is the issue. I was trying to build a simple application which is described in the tutorial for characters. After building an advertisement and understanding the...
I was working with IAR and SDK10.0 before. For some reason I have to transfer my project to Keil and SDK9.0. My program worked well for the old settings. While keeps got NRF_ERROR_SOC_NVIC_INTERRUPT_NOT_AVAILABLE...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Suppose there are 10 BLE peripherals in a room and one BLE Central,then is there any way i can get the list of available peripherals[name or id.. etc]?
I am using NRF5182...
I am using SDK_11 s130 on nrf51-dk. When err_code is any value other than NRF_SUCCESS, APP_ERROR_CHECK(err_code) will cause nRF51-dk board to reset. How can one get APP_ERROR_CHECK...
Hello All,
I have problem with ble_app_uart which are not support DFU services.
When I am implement both services device will not advertise. and when ble_nus uninitialized...
[symptom]
I want to update my application/bootloader/softdevice by DFU.
Steps are shown below.
bootloder/softdevice update
if 1 step is done, application update...
Hi, I am developing a software that connects to nRF51822 over UART. I donot have the physical device currently so I downloaded its Soft device under the impression that it...
Hi,I update my MDK from 4.7 to 5.0,my old project can open ,but can't find the device list.I want to use 5.0 and 4.7 at the same time,and I have installed the SDK6.0 when...
Hi, when I compile my project the linker gives me the following error:
._build\nrf51422_xxac_s130.axf: Error: L6200E: Symbol GPIOTE_IRQHandler multiply defined (by app_gpiote_fast_detect...
I am working with nRF52832 and SD 132 and SDK 11 (nRF5_SDK_11.0.0-2.alpha_bc3f6a0).
One of my BLE services has a characteristic with an attribute larger than 22 bytes. It...
i was working with a nrf51822 module.after about 50 that i programmed the chip with my jlink programmer (some time i program it with stlink V2) it be damaged and not worked...
I am designing a BLE device. Want to make the PCB as small as possible. to download the code/debug etc I need the a connecter on the board which can connect to the nrf52 preview...
Please excuse my ignorance, My company is designing in the nRF52832 for our first product using both ANT and BLE. From looking at the documentation on thisisant.com there...
I've got a strange problem with updating my Magnet-Characteristic.
I use a service with 4 characteristics (Gyro, Acc, Mag and Temp Values) and update them on a timer base...
Hello,
Two issues want to ask, after tried the BLE_NUS example code.
From other posts, still does not exist clear solution (example, pictures) ?
Sure has an application...
Hello,
I am working with the uart module. While configuring the uart I encounter 2 issues.
First when in the uart_init function the pin for uart output is configured...
Hi,
I am using nrf51822(128k), SD 6.0, SDK 5.2.
I found that nrf uart v2.0 app will add a "0x0A" at the end of data that I want to send.
How can I remove this?
Thank...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
I've never used Gnu's GCC before, but after 20 hours of trying and failing to install it on my macbook, I'm finding a shining hatred. I've downloaded their exhaustive list...
I migrated to nrf52 and countering some problems.
I am trying to sample 4 pins every 2ms with SAADC.
I started with Example here .
I simply changed
uint32_t ticks...