I've modified Nordic's "Nordic_Keyboard" sample to work with my custom board, just simple modifications to use custom_board.h rather than the default PC10028 configuration...
Hi,
I use HID application with S110 v8.0 profil.
I use BLE HID Keyboard example.
I put datas from smartphone to BOOT KEYBOARD OUTPUT REPORT and I whant read them by...
Hi all,
I use nRF51822 module and my environment is Eclipse + GCC + SDK 10.0. I refer to the example in path <SDK_PATH>/examples/ble_peripheral/ble_app_template, then make...
I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Support Team,
I am working on a project using the nRF54LM20B controller, and my application requires operation in a very low-power mode .
To optimize...
The nRF7002 datasheet lists that the current draw for maximum power transmits is ~170 - 260mA depending on frequency and if you are using the CSP or QFN package. Please confirm...
We are college students and hoping to have a schematic review before we work on the layout (have a very rough placement right now) and routing. Any feedback is appreciated...
I'm working through the Cellular IoT Fundamentals course. In lesson 7 exercise 1 a modem trace must be captured. I'm following the instructions but the modem trace capture...
Dear Support Team!
I'm just about to flash an external board (nRF52820) through P19 where the MCU is powered at 2.3V. I would like to use the nRF52833_DK and the PPK2 to...
Setup: nRF Connect SDK v3.4.0 (LTS), custom board based on nRF54LM20A, sysbuild with MCUboot as the only bootloader (no NSIB / b0), DTS partitions (SB_CONFIG_PARTITION_MANAGER...
Hi, We're in the product validation stage of development with nRF54L15, part of the validation is temperature cycling, we noticed that devices seem to be "stuck" in sleep...
Hello,
I'm following online courses in Nordic Academy (nRF Connect SDK Intermediate).
As indicated in the first lesson,first excercice, I added device_message_queue...
Hi everyone! I'm having difficulties in setting up a little project in which I want to pass I2S data over USB. I know I'm using the old USB Audio Class endpoints, but everything...
Hello Nordic Support Team,
I am using the nRF5340 Audio DK with the nRF Audio application provided with the nRF SDK, configured as a Unicast Server.
The board advertises...
Should sdk-zephyr carry this ring-buffer adaptation or adopt the newer upstream receive implementation from github.com/.../122772
At sdk-zephyr `3876d730`, RX BUSY remains...
Hello! I've observed that while flashing the nrf9151 modem firmware over USB it always succeeds, but over USB/IP the flashing always fails since the nrfutil tool internally...
Problem:
After every wake-up our device reports a SoC 10–28 % higher than it reported just before going to sleep.
Between sessions the nRF5340 is in System OFF via sys_poweroff...
Dear Nordic team,
I am trying to set up OTA updates by using the DFU target API on an nRF9151 DK with MCUboot and TF-M partitions. (NCS v3.4.1) My goal is to use the immutable...
