Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
https://academy.nordicsemi.com/courses/nrf-connect-sdk-fundamentals/lessons/lesson-6-serial-com-i2c/quizzes/lesson-6-quiz/
I think "i2c_read()" can only be used by I2C master...
Dear all,
I am testing Bluetooth Channel Sounding on nRF54L15 DK with nRF Connect SDK v3.3.1，and use the app on iOS 27 Beta2.
Environment: SDK: nRF Connect SDK v3.3.1...
Hello Nordic Support Team,
I'm experiencing a Bluetooth LE Channel Sounding (CS) issue between a Samsung Galaxy S26+ running Android 17 and an nRF54L15 running the RAS Reflector...
Hello Nordic Support Team,
I am working on a project using the nRF54LM20B controller, and my application requires operation in a very low-power mode .
To optimize...
The nRF7002 datasheet lists that the current draw for maximum power transmits is ~170 - 260mA depending on frequency and if you are using the CSP or QFN package. Please confirm...
I'm working through the Cellular IoT Fundamentals course. In lesson 7 exercise 1 a modem trace must be captured. I'm following the instructions but the modem trace capture...
Dear Support Team!
I'm just about to flash an external board (nRF52820) through P19 where the MCU is powered at 2.3V. I would like to use the nRF52833_DK and the PPK2 to...
Setup: nRF Connect SDK v3.4.0 (LTS), custom board based on nRF54LM20A, sysbuild with MCUboot as the only bootloader (no NSIB / b0), DTS partitions (SB_CONFIG_PARTITION_MANAGER...
Hi, We're in the product validation stage of development with nRF54L15, part of the validation is temperature cycling, we noticed that devices seem to be "stuck" in sleep...
Hello,
I'm following online courses in Nordic Academy (nRF Connect SDK Intermediate).
As indicated in the first lesson,first excercice, I added device_message_queue...
Hi everyone! I'm having difficulties in setting up a little project in which I want to pass I2S data over USB. I know I'm using the old USB Audio Class endpoints, but everything...
Hello Nordic Support Team,
I am using the nRF5340 Audio DK with the nRF Audio application provided with the nRF SDK, configured as a Unicast Server.
The board advertises...
Should sdk-zephyr carry this ring-buffer adaptation or adopt the newer upstream receive implementation from github.com/.../122772
At sdk-zephyr `3876d730`, RX BUSY remains...
Hello! I've observed that while flashing the nrf9151 modem firmware over USB it always succeeds, but over USB/IP the flashing always fails since the nrfutil tool internally...
