Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Hello. I have a project that needs an update.
The project was working before July 2022. However, now it doesn't work anymore (VsCode run/debug doesnt work) anymore. The...
Greetings,
during test of a device, we have tried uploading a shell sample in a nrf52840dk board. However for some reason this caused the board, or at least the installed...
Hi - I am using nRF5 SDK v17.1.0 and Segger Embedded Studio v6.34a. I am testing the ble_app_buttonless_dfu for pca10040_s132.
I am compiling ble_app_buttonless_dfu_pca10040_s132...
Dear Nordic Engineers
I would like to use the DFU trigger library to realize the NRF CONNECT for Desktop enter bootloader.
I found a demo in devzone: https://devzone...
Using a MAC running Monterey, VS code runs from command line on a terminal window from everywhere. When clicking on the "Open VS Code" button from the toolchain manager it...
For the nRF5xxxxx series, it looks like it has a differential ADC with 8 positive and 8 negative channels. It also looks like it has a scan mode where it will sequentially...
Hi,
I have a nrf9160DK and flashed it with Serial LTE Modem sample, however all the AT commands are just timing out.
Configuration is default and UART 0 is used.
...
Hi!
I want to connect my NRFL2401 to my computer using BLE (v4.0.0) in order to collect data from a sensor. However, the «Start Scan» button is not functional. When I click...
Hi!
I am trying to subscribe to nrf cloud with topic " prod/<TEAM_ID>/<DEVICE_ID>/jobs/rcv". After that I get Disconnect event in the MQTT handler.
Topic "prod/<TEAM_ID...
Hello Everyone,
I am using NRF52832 in my project and in my project I want to charge the device through USB C. So when we plug in USB C into the device, the NRF52832 should...
I followed the directions for pulling down the nRF Connect SDK v2.0.2 via Toolchain Manager v1.1.3 in nRF Connect for Desktop v3.11.1.
I am using Ubuntu 22.04.1 LTS 'Jammy...
Hi,
I am creating a central code from scratch, using zephyr version 2.0.1. I want to know the central code contain all the zephyr rtos property like thread in background...
Hi All,
I am trying to communicate with IC MAX17201 using I2C interface. I am able to detect the IC and communicate with it.
When I read 8bit registers from the IC I don...
Hello,
nRF5340, NCS2.0.2, vscode.
\v2.0.2\zephyr\samples\bluetooth\periodic_adv
when TX and RX work on PHY_1M, two side work well.
but when TX side set BT_LE_ADV_OPT_CODED...
Hi,
Is it correct that nrf-sdk does not support (or have any implementation for) the "NV Counters" API in TF-M ? (needed for rollback protection in the Protected Storage...
