Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Thanks Stefan. The zip file making and updating steps work perfectly for me, if I follow your steps and make it from your stock pre-built "dfu_test_app_hrm_s132.hex". My question...
Hi!
I'm trying to configure my NRF8001 module with the help of nRFgo studio. I'm using Nordic UART over BTLE service template. The module can be discovered via nRF Master...
I'm trying to make a BLE device that actually pairs securely. I posted this question on StackOverflow but didn't get any answers - maybe someone here knows more. As far as...
The CONFIG_CLOCK_CONTROL_NRF_K32SRC_EXT_FULL_SWING=y Kconfig option causes kernel booting to hang at line 505 of clock_control_nrf.c.
This is on the v1.7-branch of NCS ...
I have created a custom board containing the nRF52832. I have two copies. The first board works, meaning that I have flashed the code to it using the DK52, and I can power...
Hello,
I have been evaluating the nrf9160 DK board. And my application is using mbedtls (vanilla) and TFM (Used https_client as a starter project). The problem is that with...
Hi,
I'm new to nRF/Zephyr development and trying to integrate the OV7670 camera with the nRF52840 board. Since there was no driver for this particular camera I ported the...
I'm having a problem with what should be a very simple exercise. I'm trying to compile the Zephyr sample subsys/cpp/cpp_synchronization after adding #include <string> to the...
Hello,
I am trying to read data from LS2DE12 accelerometer MEMS chip via I2C bus and I am seeing only zeros for all 3 axes.
I can write to the various registers successfully...
Hello, I ran the nrfconnect (ver 3.7.1) in Power Profiler (ver 3.1.3) in BLE advertising.
When I run the source mode on 3000V I get normal peaks (20mA), however when I run...
Hi,
I'm interested to use AGPS in my project. Looking into AGPS example (link below) , I want to prevent using low power mode since as far as I know using this command you...
Power Profiler software returns an error after I updated it to v3.2.0 with nRfConnect v3.8.0.
Error message: Error while probing devices: EnumerateWorker json error
Resulting...
Hi,
I am working with nRF52833 DK with nRF Connect SDK. All was going great until I had to add a GNU GSL library. I need it because I need matrix multiplications with complex...
Hi,
We are working on a custom bootloader/DFU and is going to use USB CDC to perform DFU and some data transfers for version information. We use the USB CDC library both...
Hello,
SD: 122
part nrf52833
I need to do the following:
a. scan for advertisements containing a particular MAC address without connecting. This works.
b. the...
Are there any convenient ways to debug BLE connectivity issues? I have the service up and running but the connection on nRFConnect App doesn't quite go through: it remains...
Hello,
I work with the nRF5340 and want to use I2C0 (1-3 is reserved for other sensors in my project ). I already use I2C2 for a sensor and this works fine.
To use the...
Sorry I'have a question about the certification process of a BLE in a custom board.
I see that with zephyr that I can define a custom board derived fron nrf52840dk. If for...
