I am using esb in SDK 11 and my understanding is that the radio causes interrupts that are forcing and cannot be disabled. These in turn causes software interrupt 10 to be...
I'd like to read and write data to the reserved app data space while in the bootloader. Is this possible with pstorage?
Because the BOOTLOADER_SETTINGS_ADDRESSS = 0x0003FC00...
Hi,
I am using 'pstorage_update' to store data in the internal flash. Whenever the number of bytes that should be written matches the size of a storage block everything...
Has anyone tried to generalize this example to different sized variables? What I would like to do is allocate a data structure, write that to flash, and recall it at a later...
I've a PCA10036 V1, I change the IC to nRF52822 QFAA-B016. With nRF5_SDK_11.0.0-2.alpha_bc3f6a0 and SD: s132_nrf52_2.0.0-7.alpha_softdevice, the programme started but if I...
Hi
We are developing software for the nRF51 with Keil under VirtualBox. Previously we used the PCA10000 dongle with the Master Emulator and MCP without issue. Now, with...
We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
My product is based on nRF52840.
I have downloaded nRF5_SDK_17.0.2_d674dde.
Example: ble_central_and_peripheral / ble_app_interactive.
pca10056 doesn't have iar project...
Now let nrf9160 register the network to the analog base station, set the network mode of the device to cat-m, and currently use the analog base station to send SMS, the device...
Hello everyone,
I'm working on a mesh application based on the light switch example. For this purpose, I'm using one nRF52DK (PCA10400) as the server, another one as the...
nRF Connect SDK - Install tool chain - Verify All - I encounter few errors . I have attached the log file. Kindly guide me how to correct those errors. MY OS is Ubuntu 20...
Hello, I just brought this board and I was playing with it but I'm unable to get it working, I'm using platformIO IDE and I have configured it to use Arduino framework but...
I've been having a ton of issues getting any of the application code to run on my Thingy91. Just tried updating the Modem FW to 1.2.2, however I'm not able to place my Thingy91...
Hi:
52840 with softdevice, I use External low frequency oscillator (32.768K) ,the system run normal,but some days later,system can't run. So,I find the problem，the problem...
The Bluetooth Core Spec version 5.2 says that the " maximum number of CISes in a CIG shall be 31."
Can the nRF52840 support 31 concurrent CISes in one CIG? If not what is...
I want to load the GPS routine project of 9160, but it fails. The error prompt is as follows:
one step
When I click OK, the following prompt appears
two...
Hi,
I have nRF52833 and nRF9160 on my custom board. Due to limited space available, trying to use a common SWD interface between the two SoCs. As follows: 1) SWDIO and SWDCK...
I add the MAC of acquisition device in the broadcast initialization of nrf52810 serial port routine, it can display complete. But I added the Mac to the template broadcast...
Hi ,
My firmware is almost done, and now is the time to optimise power cunsomption.
First, my software has a special mode. Each day it wakes up, communicate with a sensor...
Hello,
We are developing products with nRF52810 MCU. There are only 100 bytes ROM left now. We hope to update bootloader via Buttonless DFU in single bank way. Is it available...
I want to use the four peripherals UART0, UART2, UART3, and I2C_1 on nrf9160. When I was building the project, I encountered the following error.
Here my prj.conf
...
Hi,
I received a Thingy91 and am unable to commission it to nrFCloud.
The Thingy91 skipped orange breathing as mentioned in the manual here (step 4). It went directly...
