Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Hello,
We use the nrfx spis driver for communication between a ST processor (master) and a Fanstel BT840 module (nRF52840).
We have upgraded ncs from 2.6.0 to 3.2.1 and...
I am using a GPIO pin ( P1.05 ) as a reset signal for an external CPU component. The pin functions correctly and stays low when tested in a basic GPIO application. However...
I'm using NCS 3.2.4. When USE_PARTITION_MANAGER is active, the ARM linker script defines ROM_SIZE as PM_SIZE (the full app partition) without subtracting CONFIG_ROM_END_OFFSET...
I have a simple code. send msg to a message queue. and handle the message in another thread. I my old environment ncs2.4.0. I looks works well. // after get msg queue. to...
Dear Nordic Engineer,
Hello!I am planning to develop a 2.4G, BLE and USB mouse. Both the dongle and the mouse device will use the NRF52840. I want to use BLE and ESB simultaneously...
Hello,
For my prject I need to tiggrer a timer start using a pin. I'm trying do do it using PPI but it seems that GPOITE can only create events on input pins. If anyone...
The MCU is NRF54L10, the SDK is NCS2.9.1, and the firmware is updated using MCUboot update mode.
Configuration as follows：
# sysbuild.conf
SB_CONFIG_BOOTLOADER_MCUBOOT...
Hi,
I write this information for the sake of completeness. I don´t need Zigbee2MQTT support from you. Instead, support with the Zigbee firmware is required.
I´m working...
Hello,
I am currently testing a setup combining the nRF5340DK and nRF7002EK using NCS/Toolchain v3.0.0 .
I need to reassign the 8 GPIO pins (including Bucken, Grant, etc...
Background:
Platform : nRF52832 with nRF Connect SDK (NCS) v3.1.0
BLE Roles : The device operates simultaneously as:
A BLE Central (NUS Client) , connecting to an...
While installing the nrf connect extension for VS code and installing the SDK and toolchain I have encountered the same issue multiple times. The toolchain and SDK got installed...
Hardware: nRF5340 DK
nRF Connect SDK: v2.6.1
Description:
I am working on a project where there is a need to transfer a large amount of data from NET to APP core. We...
Hello,
I am working with nRF9160 already since SDK v2.1.2 and with every update there are some functions not working anymore, although not mentioned anywhere in the documentation...
I am currently working on a FOTA implementation I am using nRF9160 DK with nRF Connect SDK v3.1.1 and the LwM2M client sample (/samples/cellular/lwm2m_client/). I am using...
Hello All, I hope everyone is doing great. I am an embedded enthusiast and i recently started working on nRF boards. I am currently facing error while setting up my custom...
