Hi Guys,
I know this is more for software issues. But I was curious as to where I can find trusted case providers/makers for the nrf51822 Beacon. Can anyone from the community...
Hi,
Has anyone converted the Adafruit graphics library for Arduino, Adafruit_GFX.h, to be compatible with the nRF51?
Could you please advise on how to convert this Arduino...
Hi all,
I have a few questions:
How is that ADC's common mode rejection capabilities? Rejection for 60 Hz interference, etc...
The datasheet has "typical...
Hi all !
I'm trying to evaluate the throughput i can have between a Motorola 4G and the nrf51. The nRF51 is the peripheral and the phone is acting as a central.
To do...
I have a digital microphone chip, it has the CLK, DATA, LR_SEL three pins, now I will pick up the three pin nrf5283 three pin is as follows: CLK connectionI2S_CONFIG_SCK_PIN...
Hello, Nordic Team, I'm embedded designer from Russia, discovered your amazing wireless MCU NRF52832. I looked through your SDK and peripheral drivers, and unfortunately found...
Hi!
I just saw the MQTT example that has been merged in the master branch and tried to run it on my DK (NB-IoT). Without changing anything in the code or configuration the...
Following my last post a few days ago, I was finally able to communicate with a slave via the TWI interface, thank you very much for your help! This time, I have a problem...
Hi,
I'm using nrf52832 as host and peripheral concurrently, with soft device s132. I know that peer manager can handle both host and peripheral.
I now have a need to remove...
Hi everyone,
We are (still) in the process of evaluating the nrf9160 with the DK.
Our use case is the following one: we want the nrf9160 to send periodic messages in PSM...
Hi, We've developed an IoT platform that runs on Raspberry Pi's that has just been released and we're actively seeking beta testers (see www.omniot.com ). In short the platform...
This is a break from another thread where I was having issues getting the .emproject to show up. Now it is complaining about a missing file...
OK so I went back to the getting...
Hi, I wrote a simple program to communicate with ICM20948 IMU .
The IMU correctly acknowledges its address.
But, when I try to read its WHO_AM_I ID, the program halts...
In previous SDKs (e.g. version 15.0) the following macros were defined in app_util.h
As described in this post these needed to be modified to support more than 15 connections...
I am trying to do the segger development for the 9160 lte ble gateway. When I do the setup info for segger I keep getting a popup saying it can't find the .emproject file...
Hi
I'm working my way through learning how develop BLE Services and Characteristics for an NRF52840. I'm using the 'ble_app_template' example from the SDK (version 15.2...
Hi,
I have the following lines:
NRF_LOG_ERROR ( "This is an ERROR message." );
NRF_LOG_WARNING ( "This is a WARNING message." );
NRF_LOG_DEBUG ( "This is a DEBUG...
I am inquiring about an issue with the SPIM communication. I am reading the who am i sensor of an MPU9250 and it reads 0x71, as it should most of the time but not always....
uVision V5.26.2.0
Error #541: 'NordicSemiconductor::Device:Startup:8.24.1' component is missing (previously found in pack 'NordicSemiconductor.nRF_DeviceFamilyPack.8.24...
I have a complete implementation of OTA DFU where iOS app performs a DFU to a nRF based BT Device. Now i am implementing a fix for the situation where:
During DFU, if...
Hi,
I am currently having issues compiling the thingy52-mesh-provisioning demo from github with cmake. The Readme talks about using SES to compile it, which works fine,...
